TSC TDM-20 User Manual Download Page 24

Page: 24 / 64

TDM-30:

Charging the battery when the printer

turns on

Charging cycle

LED version

LCD version

1. Charging the battery when

the printer turns on.

Charging level:

0~30%

1 block blinking

Charging level:

0~25%

Charging level:

30~60%

2 blocks

blinking

Charging level:

25~50%

Charging

level:60~100%

3 blocks

blinking

Charging level:50~75%

Charging

level:100%

4 blocks

blinking

Charging level:

75~100%

Solid 4 blocks

Charging level:

100%

2. Power saving mode

1. Printer status LED blinks amber light.

2. Push power on/off button when charging the battery, the printer will leave power saving mode.

3. The power saving mode will be ended if the power supply is removed from the printer.

3. Fully charged then turn off

the printer automatically.

Charging

mode

Power

saving

mode

Fully charged then turn off

the printer automatically.

Summary of Contents for TDM-20

































































Search results

Summary of Contents for TDM-20

Reviews:

Related manuals for TDM-20

Brands by name

Popular brands

TSC TDM-20, User Manual

Search results

Summary of Contents for TDM-20

Reviews:

Related manuals for TDM-20

Brands by name

Popular brands