TSC M23 series Page 33 User Manual Download

Page: 33 / 69

4.1.2.2 Black Sensor:

Press the

button under

and

icon to select the sensor calibration

mode, and press the

under “

]

” icon to start sensor calibration.

4.1.2.2.1 Auto Bline:

When enter the [Auto Bline] option, you will see following message.
Normally, we use Auto Bline to calibrate sensor sensitivity.

Insert label on the black mark sensors, and press the

button under “V” icon

to start sensor calibration.

Note:

DO NOT align black mark to the black mark sensor when
calibrate black mark sensor or sensor will be calibrated
incorrectly.

Press the

button under “+” and “-“ icon to increase and decrease

Stock AD value, and press the

under “V” icon to calibrate sensor.

When sensor is calibrated successfully, press the

button under

“

” icon to return to the previous page.

If “FAILED” is shown on the LCD display, please check if only paper

Auto Bline

Manual Bline

]

Insert label ...

Then hit Enter

Bline Calibrate

150

+ - V

Calibrating ...

Stock AD = 256

SUCCESSFUL

Stock AD = 150

Summary of Contents for M23 series






































































Search results

Summary of Contents for M23 series

Reviews:

Related manuals for M23 series

Brands by name

Popular brands

TSC M23 series, User Manual

Search results

Summary of Contents for M23 series

Reviews:

Related manuals for M23 series

Brands by name

Popular brands