7
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values
given. The above-mentioned causes may lead to higher exposure to
vibrations during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.
wrench (
13
) exerting a slight force as the nut automatically tightens
up during operation. Observing this recommendation will help
avoiding damage to the motoreducer casing during the disk
removal.
NOTE:
The spindle lock button (
6
) can be pressed only when the spindle is
stopped!
Never use a disk with improper maximum admissible speed!
n
Trial start up
After inserting a disk and after connecting the grinder to the mains check
whether the disk is properly fixed and whether it rotates without any
obstacles.
BEFORE YOU START WORKING:
The initial/trial start up should be carried our away from people.
1. Make sure that the power source parameters match the parameters
presented on the grinder nameplate.
2. Make sure that the grinder power switch (
8
) is in off position.
3. When using an extension cable make sure the extension cable
parameters and conductor sections match the grinder parameters. It
is recommended to use the shortest extension cables possible. The
extension cable should be fully unwound.
REGULAR OPERATION:
n
Mounting the side handle
n
Switching on/off
NOTE:
For safety reasons always use the side handle (
1
).
Before you switch on the tool check if the switch (
8
) is in working order
Depending on the operating requirements screw the side handle to the
and returns to “Off” position after releasing. The device is fitted with a
end in one of th
re
e seats provided in the grinder head (see: Fig.
B
, p.1).
''soft-start'' feature to reduce the value of startup current and to
n
Mounting the disk guard
decrease the start up impact. To protect the grinder against accidental
NOTE:
Before you install or remove the disk guard, make sure that the
start, the switch (
8
) is equipped with a locking lever (
9
).
device switch is in off position and that it is disconnected from the mains.
To start the grinder:
.
To cut or grind with grinding or cutting disks it is necessary to install the
1 - press the locking lever (
9
) towards the arrow (see: Fig.
D
, p.1),
disk guard (
2
). Adjust the guard position to the operation performed.
2 - press the switch button (
8
). Speed increases as the switch button is
The closed side of the guard should be always directed towards the
depressed.
operator. To install the disk guard:
To stop the tool just release the switch.
ź
Place the grinder with the spindle (
11
) up.
To start the tool for continuous operation press the locking lever (
9
)
ź
Loosen the guard clamp (
10
) and remove the disk guard (
2
) to align
the boss on the guard clamp with the boss on the bearing box
(see: Fig.
C
p.1).
ź
Adjust the guard by turning it to position required and secure the
fixing clamp.
n
Grinding tools assembly
(see: Fig.
F
,
G
,
H
p.2)
NOTE:
Before you install or remove the grinding disk, make sure that the
device switch is in off position and that it is disconnected from the mains.
Before installation clean the grinder spindle and all fixing components.
Make sure the admissible size and speed of the grinding disk matches
the parameters presented on the grinder nameplate. The grinding disk
should be installed without any clearance on the fixing flange. Do not
use any reduction washers or adapters.
To install a disk:
1.
Place the grinder with the spindle (
11
) up. Insert the fixing flange (
4
)
with its bottom projecting part with a groove onto the spindle shaft
to mesh the flange on the spindle.
2. Insert a disk (
12
) with its convex part down onto the upper
projecting part of the fixing flange.
3. Screw the compression nut (
3
) onto the spindle to secure the disk
properly. (The compression nut has a concave and convex side.
Depending on the rated disk thickness it can be applied on one or the
other side. (see: Fig.
G
p.2).
4. Press the spindle lock button (
6
) and tighten the nut using the pin
towards the arrow, press the switch (
8
), then press the locking lever
farther towards the arrow.
To stop the tool working locked for continuous operation:
1-press the switch to the end,
2- release it (see: Fig.
E
, p.1).
NOTE:
Never put the grinder aside when the switch is locked. When the tool
is not used disconnect the power cord plug from the mains.
n
Tips regarding the operation
ź
The objects to be machined that do not rest securely under their own
weight should be fixed properly.
ź
Avoid excessive pressure exerted on the disk. Grinding should be
carried out using the weight of the tool. Only slight pressure is allowed
when cutting. Excessive pressure reduces the disk speed, which results
in producing rough surfaces. In addition, it results in overheating and
damage to the motor.
n
Grinding direction
When using a new grinding disk move the grinder back (B direction)
(see: Fig.
I
, p.2), then the new disk edge will be rounded, which will allow
the user to move the tool in any direction.
n
Grinding angle
Do not use the whole disk surface to grind, use its edge only.
For efficient grinding the angle between the disk and machined part
º
º
should range from approx. 15 to 30 (see: Fig.
I
, p.2).
3 minutes or more
1 minute or more
Trial operation
period
After disk
replacement
At first start up
Summary of Contents for TMS23020
