Tryton TMS23020, Operating Instructions Manual

Page: 5 / 56

4
e) Power tools require maintenance. Check power tools for running faster than their rated speed can break and fly apart.
concentricity or jamming of moving parts, any cracks and all
d ) The outside diameter and the thickness of your accessory
other factors affecting the power tool work safety. If any
must be within the capacity rating of your power tool.
damage to the power tool is detected, it should be repaired
Incorrectly sized accessories cannot be adequately guarded or
before use. Improper power tool maintenance is a reason for many
controlled .
accidents.
e ) The arbour size of wheels, flanges, backing pads or any other
f) Cutting tools should be sharp and clean. Keeping sharp cutting
accessory must properly fit the spindle of the power tool.
edges in good condition reduces the risk of jamming and facilitates
Accessories with arbour holes that do not match the mounting
operation.
hardware of the power tool will run out of balance, vibrate excessively
g) Power tools, equipment, working tools etc. should be used and may cause loss of control.
according to this user's manual taking into account
f ) Do not use a damaged accessory. Before each use inspect the
operating conditions and the work to be done. Misusing a
accessory such as abrasive wheels for chips and cracks,
power tool can result in dangerous situations.
backing pad for cracks, tear or excess wear, wire brush for
h) At low temperatures and after a long brakes in operation it is
loose or cracked wires. If power tool or accessory is dropped,
recommended to turn the power tool to operate it with no
inspect for damage or install an undamaged accessory. After
load for a few minutes to provide proper grease distribution
inspecting and installing an accessory, position yourself and
inside its driving mechanism.
bystanders away from the plane of the rotating accessory
i) Use soft, damp (cannot be wet) cloth and soap to clean power and run the power tool at maximum no-load speed for one
tools. Do not use petrol, solvents and other agents that may minute. Damaged accessories will normally break apart during this
damage your equipment .
test time.
j) Power tools can be stored/carried after making sure that all g ) Wear personal protective equipment. Depending on
moving components are locked and protected against application, use face shield, safety goggles or safety glasses.
release with original devices intended for this purpose.
As appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or
k) Store power tools in a dry, dust and water-protected place.
workpiece fragments. The eye protection must be capable of
l) Carry your power tool in its original packaging to provide
stopping flying debris generated by various operations . The dust mask
protection against mechanical damage.
or respirator must be capable of filtrating particles generated by your
WARNING! General warnings regarding the use of
operation. Prolonged exposure to high intensity noise may cause
power tools.
hearing loss.
Repair :
h ) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate area of
operation.
i ) Hold power tool by insulated gripping surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord.
Cutting accessory
contacting a "live" wire may make exposed metal parts of the power
tool "live" and shock the operator.
j ) Position the cord clear of the spinning accessory. If you lose
control, the cord may be cut or snagged and your hand or arm may be
ANGLE GRINDER
pulled into the spinning accessory.
Safety Warnings Common for Grinding, Sanding,
k ) Never lay the power tool down until the accessory has come
Wire Brushing, Polishing or Abrasive Cutting-Off
to a complete stop. The spinning accessory may grab the surface
Operations:
and pull the power tool out of your control.
a) This power tool is intended to function as a grinder, sander,
l ) Do not run the power tool while carrying it at your side.
wire brush, polisher or cut-off tool. Read all safety warnings,
Accidental contact with the spinning accessory could snag your
instructions, illustrations and specifications provided with
clothing, pulling the accessory into your body.
this power tool. Failure to follow all instructions listed below may
m ) Regularly clean the power tool's air vents. The motor's fan will
result in electric shock, fire and/or serious injury.
draw the dust inside the housing and excessive accumulation of
b ) Do not use accessories which are not specifically designed
powdered metal may cause electrical hazards.
and recommended by the tool manufacturer. Just because the
n ) Do not operate the power tool near flammable materials.
accessory can be attached to your power tool, it does not assure safe
Sparks could ignite these materials.
operation.
o ) Do not use accessories that require liquid coolants. Using
c ) The rated speed of the accessory must be at least equal to
water or other liquid coolants may result in electrocution or shock.
the maximum speed marked on the power tool. Accessories
a) Power tools can be repaired by competent persons only who
use original spare parts.
It will provide safe operation for the power
tool.
b) If a fixed power cord is damaged, to avoid risks it should be
replaced by power tool manufacturer or in a specialty repair
shop or by a qualified person.
WARNING!
While operating power tools it is necessary to observe basic
work safety rules to avoid fire, electric shock or mechanical
injury.