Tryton TFV12, Operating Instruction

Page: 5 / 52

5
b) The supplied charger should only be used for charging Fig.C 11.
batteries that are supplied together with it. Charging other
batteries may cause breaking and disintegration of the battery, bodily
harm, or fire.
c) Do not disassemble the charger.
d) The charger is designed exclusively for indoor use. It must not
be exposed to water or moisture.
e) Charge only in an ambient temperature between 15-25
degrees.
f) Do not insert metal objects of any kind into the charger.
The device is dedicated to drive in and out screws, drilling boreholes in
such materials as steel, wood, plastics, etc. The combo drill and
screwdriver is designed exclusively for DIY applications
.
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
n
The set contains:
maintained properly, the vibration level may differ from the values given.
ź
Cordless drill/s crewdriver -1
The above-mentioned causes may lead to higher exposure to vibrations
ź
Battery - 1
during the whole work time. One must implement additional safety
ź
-1
measures to protect the operators from exposure to vibrations, such as
ź
:
maintenance of the electric tool and work tools, assurance of proper
- -1
hand temperature, or determination of the sequence of work operations.
- - 6 s (P H 1, P H 2, PZ1, PZ2, SL 5 , SL 6 )
- - 6 s ( 1,5; 2,5; 3; 4; 5 ; 6 mm)
n
Charging the battery
ź
Carrying case -1
The driver is supplied with a partially charged battery. Charge the battery
ź
-1
fully before use. It is recommended that the first charging session lasts at
ź
O perating instruction -1
least 5 hour s .
1.
The numbering of device components refers to graphics presented on page
2 of the user's manual:
Fig.A 1. Keyless chuck
3. Connect charger to an electrical socket 100-240 V, 50/60Hz.
2. Clutch control knob
n
Battery charging indicator
3.
4. Rotation direction switch
5. H andle
6.
After charging, disconnect the charger and remove the battery.
APPLICATIONS AND CONSTRUCTION:
Despite using the tool according to its intended application it is
impossible to eliminate certain residual risk factors. Considering the tool
construction the following risks may occur when operating the tool:
- Touching the rotating drill bit with the hand
operator's clothes .
- Burns when changing drill bits (Drill bits heat up intensely during
operation; use protective gloves when changing the drill bit).
- Throwing back machined object or its fragment.
- Bending/breaking the drill.
Device components
The tool must not be used for work requiring a professional tool.
Any use of the that is not in observance with the above-
mentioned purpose is forbidden, leads to the loss of warranty, and
relieves the manufacturer from responsibility for the resulting damage.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the
surroundings.
Fig.F
Fig.G
device
n
Battery
Battery lock clip
On/off switch
The lithium-ion battery can be charged at any moment, without
detriment to its life. Interrupting the charging process does not entail a
TECHNICAL PARAMETERS
or
pc .
pc .
pc .
Working bits set
magnetic tip for bits with a 1/4" holder pc .
bits pc .
PREPARATION FOR WORK:
drills pc .
pc .
Warranty card pc .
pc .
Press the battery lock button ( 8 ) and remove the battery ( 7 ) from the
drill-driver ( see fig. B ).
2. Connect the battery ( 7 ) to the charger ( 11 ) (see fig. C ).
Battery capacity indicator
Fastener to hang on the belt
Charger
12. Clutch setting indicator
13. Drilling setting pictogram
14. Left-threaded fixing screw
:
Charger
7.
8.
9.
10. Auxiliary lighting
The red battery lamp is lit during the charging process. When the battery
is fully charged, the red lamp goes out and the green one is lit.
The charging current reduces with the charging progress. After about 3
hours the charging current reaches the stable, minimum value (trickle
charging) to prevent battery overcharging and damage.
MODEL TFV12 TFV18
Rotation speed under no-load conditions
Supply voltage
Chuck clamping range
Sound pressure level (LpA)
Sound power level (LwA)
Vibration level according to:
t olerance of measurements K=1,5 m/s²)
EN 60745
(
Weight (with battery)
B attery type Li-ion
Rated voltage
Charging time
Mains voltage
0-700 rpm
DC 12 V
100- 2 4 0 V
3 -5 h
1 2V
2
2,19 m/s
92 dB(A)
81 dB(A)
1,030 kg
ø 0,8-10 mm
Electric capacity 150 0mAh
DC 18 V
1,135 kg
T olerance of measurements pA, KwA 3 dB(A) K
1 8V
B attery charger
Frequency 50/ 60 Hz
Output current (DC) 15V/ 0,33A 21,5V/ 0,37A
Power consumption 5W 8W