TRW TA S40 Series Service Manual Download Page 35

Page: 35 / 60

GROUP 0603-V-003-0207

STEERING

DocID

TRW TAS STEERING GEAR

Page 1-35

Review Draft

Step Bore gears

- Install the dirt & water seal (53) with the

bearing and seal tool (long end), making sure it is not cocked.
Press the seal only until it seats against the bearing.

DON'T

PUSH IT IN FARTHER.

Liberally pack the roller bearing and new seals with clean, high
temperature industrial grease, Exxon Polyrex* EP2.

Lightly oil new seal rings (11 & 12) and assemble in valve
housing mounting face groove.

TAS40, 55, 65, 66:

Oil new seal ring (11) and assemble in valve

housing mounting face groove.

TAS85:

Oil new seal ring (11) and assemble in valve housing

pilot groove.

Install dirt & water
seal

Assemble seal
rings

Grease

Press seal into
housing

J37705 (TAS40)
J37071 or J37071-A
(TAS55, 65, 66)
J38779 (TAS85)
Press

All gears

- Assemble new seal (43) onto bearing and seal

tool (short end) so the lip with the garter spring is toward the
shoulder of the tool. Working from the side cover side of the
housing, pilot the seal tool into the washer and bearing and
press with a force of

100-800 lb (445-3,560 N) until the seal is

seated ﬁrmly.

Step Bore gears with Retaining Ring only

- Install the inside

retaining ring (48) from the side cover opening. Seat the ring
ﬁrmly in the retaining ring groove.

Standard gears only

- Install washer (50) into the side cover

side of the housing seal bore with the small diameter piloted
into the retaining ring.

Install washer

Standard gears

- Liberally pack the area between dirt seal (51)

and pressure seal (43) including roller bearing with clean, high
temperature industrial grease, Exxon Polyrex* EP2.

Grease the bearing
and seal area

*Trademark of Exxon Oil Corp.

If you are working with a housing with

an unmachined trunnion face, you may

need to square the housing to the press with shims for step 4.

J37705 (TAS40)
J37071 or J37071-A
(TAS55, 65, 66)
J38779 (TAS85)
Press

Summary of Contents for TA S40 Series





























































Search results

Summary of Contents for TA S40 Series

Reviews:

Related manuals for TA S40 Series

Brands by name

Popular brands

TRW TA S40 Series, Service Manual

Search results

Summary of Contents for TA S40 Series

Reviews:

Related manuals for TA S40 Series

Brands by name

Popular brands