TRW TA S40 Series Service Manual Download | Manualshive

Page: 50 / 60

background image

Page 1-50

TRW TAS STEERING GEAR

DocID

STEERING

GROUP 0603-V-003-0207

File Last Modified: September 17, 2012 10:18 am

49

Install input shaft
seal

The input shaft seal must be square

in the seal bore and installed to the

correct depth.

30.

Apply clean grease (Exxon Polyrex* EP2) to the outside and
inside diameters (ﬁll cavity between the lips) of the new input
shaft seal (4) and assemble it, garter spring side ﬁrst over the
input shaft. Align seal in the valve housing seal bore.

Place seal installer tool, small diameter end ﬁrst, over the input
shaft and against the seal. Tap the seal installer tool until the
tool shoulder is squarely against the valve housing. This will
correctly position the seal in the housing bore just beyond the
retaining ring groove.

Remove any seal material that may have sheared off and is in
seal bore and retaining ring groove.

J37073
Hammer

31.

Insert new retaining ring (3) into its groove in valve housing (10).

Insert retaining
ring

32.

Pack the end of the valve housing bore around the input shaft
with clean, high temperature industrial grease, Exxon Polyrex*
EP2. Apply more of the grease to the inside of a new dirt and
water seal (2) and install it over the input shaft. Seat the seal in
the groove behind the serrations and against the valve housing.

Install dirt & water
seal

Grease

*Trademark of Exxon Oil Corp.

«
...
48
49
50
51
52
...
»

Summary of Contents for TA S40 Series





























































Reviews:

No comments

Related manuals for TA S40 Series

IC-215P-AW1-W10

Brand: MicroTouch Pages: 33

Brand: Corsair Pages: 2

Brand: PortSignum Pages: 24

CyberView RP-117-TCS

Brand: Austin Hughes Electronics Pages: 1

Chassis C2234PW

Brand: 3M Pages: 49

Technicolor TCA200

Brand: iControl Pages: 11

Brand: Spring Air Systems Pages: 32

Brand: Crestron Pages: 2

NICE Era TOUCH HSTS2FR

Brand: Allo RemoteControl Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands