TruSteel AV30 Pre-Installation Download Page 12 | Manualshive

Page: 12 / 37

background image

AV30 PRE-INSTALLATION REQUIREMENTS | AV30 Pre-Installati on Requirements | v. 3.0

12 / 37

WATER HEATER INSTALLATION

[Picture Caption: Hubbell HX Electric Water Heater (left), Hubbell NX Gas Water

Heater (right)]

ELECTRIC WATER HEATER: Model HX

Tankless Electric Water Heater

Available in 33-36 KW Three Phase Voltages

The Hubbell model HX Tankless electric water heater is a highly reliable and easily

maintained heater designed for operation in a commercial or industrial application.

The Hubbell HX Tankless heater is compact, extremely efficient, takes up minimal

space and reduces operating costs.

Electric Water Heater Technical Documents

·

Model HX / TX Brochure PDF

·

Model HX / TX Written Spec PDF

·

Model HX / TX O&M Manual PDF

GAS WATER HEATER: Model NX300

Tankless Electric Water Heater

Available in 33-36 KW Three Phase Voltages

The Hubbell model HX Tankless electric water heater is a highly reliable and easily

maintained heater designed for operation in a commercial or industrial application. The

Hubbell HX Tankless heater is compact, extremely efficient, takes up minimal space and

reduces operating costs.

Important Note!!

Gas Heater will require an external flow switch AND an strap-on

aquastat. Your plumber can provide these or you can purchase them below.

«
...
10
11
12
13
14
...
»

Summary of Contents for AV30






































Reviews:

No comments

Related manuals for AV30

Brand: Keithley Pages: 149

Brand: NEC Pages: 54

Brand: Hammer Pages: 42

Brand: EuroLite Pages: 28

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brand: M-Audio Pages: 36

Brand: Vahterus Pages: 31

Brand: Panasonic Pages: 23

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: Coba Pages: 2

Brand: BH FITNESS Pages: 24

Brand: Best Fitness Pages: 26

Brand: TRX Pages: 2

Brand: Flex-A-Seal Pages: 7

Brand: Topcon Pages: 38

Brand: AGCO Pages: 44

Aesculap S4 FW103R

Brand: Braun Pages: 39

Brand: Heitronic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands