Truen TCAM-570-X18H User Manual Download Page 4

                                                                                                                           

TCAM-570-X18H User Manual

 

 

1.3 Megapixel Speed Dome User Manual 

 

4/55 

           

 

 

1. Introduction 

About this manual 

This User Manual provides information on operating and managing the premium network camera, TCAM-

570-X18H. The Manual includes instructions of installation, operation and configuration of TCAM-570-X18H 

as well as how to make troubleshooting. 

Features 

TCAM-570-X18H is a 1.3M PTZ network-based camera with remote live monitoring, audio monitoring and 

control via an IP network such as LAN, ADSL/VDSL, and Wireless LAN. 

 

Camera 

 

1/3

” Solid State Progressive CCD Scan 

 

X18 optical zoom 

 

True Day & Night (ICR) 

 

WDR (Wide Dynamic Range) 

 

Privacy Mask Function 

 

Video 

 

Highly efficient compression algorithm, H.264 & MJPEG support 

 

Resolutions: CIF (352x240) 

– HD (1280x720)   

(Note:1280x960 will be supported by further firmware. )   

 

Wide range of transmission rates: 32kbps ~ 8Mbps 

 

Various transmission modes: CBR, VBR 

 

Motion detection 

 

Composite video output 

 

HD-SDI video output (Option) 

 

Audio 

 

Multi-transmission  mode:  Simplex  (TCAM-570-X18H 

  Client  PC  or  Decoder,  Client  PC  or   

Decoder 

 TCAM-570-X18H), Full Duplex 

 

 

Network

 

 

Fixed IP & Dynamic IP (DHCP) support 

 

1:1, 1:N support 

 

Multicasting 

 

Various types of Protocol : TCP/IP, UDP, Multicast, DHCP, SMTP, HTTP, SNMP, RTP, RTSP 

Summary of Contents for TCAM-570-X18H
























































Reviews: