background image

14

S

ection

 3 — c

ontrolS

 & o

peration

• 

Watch for holes, ruts, bumps, rocks, or 

other hidden objects. Uneven terrain could 

overturn the machine. Tall grass can hide 

obstacles.

• 

Do not turn on slopes unless necessary; 

then turn slowly uphill and use extra care 

while turning. Turning up a slope greatly 

increases the chance of a rollover.

• 

Avoid stopping when driving up a slope. If it 

is necessary to stop while driving up a slope, 

start up smoothly and carefully to reduce 

the possibility of flipping the tractor over 

backward.

Mowing

 WARNING

To help avoid blade contact or a thrown object injury, keep 
bystanders, helpers, children and pets at least 75 feet from 
the machine while it is in operation. Stop machine if anyone 
enters the area.

 WARNING

Make certain the area to be mowed is free of debris, sticks, 
stones, wire or other objects that can be thrown by the 
rotating blades.

 WARNING

 Plan your mowing pattern to avoid discharge of materials 
toward roads, sidewalks, bystanders and the like. Also, 
avoid discharging material against a wall or obstruction 
which may cause discharged material to ricochet back 
toward the operator.

 WARNING

Be careful when crossing gravel paths or driveways. 
Disengage the PTO and raise the deck to the highest 
position before crossing.

Note: Do not engage the mower deck when 

lowered in grass. Premature wear and possible 

failure of the ‘V” belt and PTO clutch will result. 

Fully raise the deck or move to a non grassy area 

before engaging the mower deck.
• 

Mow across slopes, not up and down. If 

mowing a slope, start at bottom and work 

upward to ensure turns are made uphill.

• 

Do not mow at high ground speed, 

especially if a mulch kit or grass collector is 

installed.

• 

Do not cut the grass too short. Short grass is 

prone to weed growth and yellows quickly 

in dry weather.

• 

Always operate the tractor with the throttle 

in the FAST position while mowing.

• 

On the first pass pick a point on the 

opposite side of the area to be mowed.

• 

Engage the PTO clutch using the PTO switch 

and move the throttle control or throttle/

choke control to the FAST position. 

• 

Lower the mower deck to the desired height 

setting using the lift handle.

• 

Slowly and evenly push the forward drive 

control pedal forward to move the tractor 

forward, and keep the tractor headed 

directly toward the alignment point

• 

For best results it is recommended that 

the first two laps be cut with the discharge 

thrown towards the center. After the first 

two laps, reverse the direction to throw the 

discharge to the outside for the balance of 

cutting. This will give a better appearance 

to the lawn.

• 

Do NOT attempt to mow heavy brush and 

weeds or extremely tall grass. Your tractor is 

designed to mow lawns, NOT clear brush.

• 

Keep the blades sharp and replace the 

blades when worn.

• 

When approaching the other end of the 

strip, slow down or stop before turning. A 

U-turn is recommended unless a pivot or 

zero turn is required.

• 

Align the mower with an edge of the 

mowed strip and overlap approximately 3”.

• 

Direct the tractor on each subsequent strip 

to align with a previously cut strip.

• 

To prevent rutting or grooving of the turf, if 

possible, change the direction that the strips 

are mowed by approximately 45° for the next 

and each subsequent mowing.
Note: When stopping the tractor for any 

reason while on a grass surface, always:

• 

Engage the parking brake, 

• 

Shut engine off and remove the key. 

• 

Doing so will minimize the possibility 

of having your lawn ‘‘browned’’ by hot 

exhaust from your tractor’s running 

engine.

Manual Lift Lever

To raise or lower the cutting deck, move the lift 

lever to the left, then place it in the notch best 

suited for your application.

Operating the PTO 

Operate the PTO clutch as follows:
1. 

Move the throttle to approximately the mid-

throttle position.

2. 

Pull the PTO switch upward to the “ON” 

position. 

3. 

Advance the throttle to the operating speed 

(full engine speed).

4. 

The operator must remain in the tractor seat 

at all times. If the operator should leave the 

seat without turning off the PTO switch, the 

tractor’s engine will shut off.
NOTE: Always operate the tractor with the 

throttle lever in the FAST position for the 

most efficient use of the cutting deck or 

other (separately available) attachments.

Notes

Summary of Contents for Zero-Turn Tractor













































Reviews: