Troy Built Zero-Turn Tractor, Operator'S Manual

Page: 10 / 44

Controls & Operation
3
10
G
(B)
(L) †
(M)
†
(D)
(H)
(E)
(N) †
(C)
(J)
(K)
(F)
(I)
† -- If Equipped
(F)
(O)
(P)
(R)
(Q)
(A)
Figure 3-1
Note: This Operator’s Manual covers several
models. Tractor features may vary by model. Not
all features in this manual are applicable to all
tractor models and the tractor depicted may differ
from yours.
Note: References to LEFT, RIGHT, FRONT, and REAR
indicate that position on the tractor when facing
forward while seated in the operator’s seat.
Steering Wheel (A)
The steering wheel is used to control the direction
of the tractor.
Deck Height Index (B)
The deck height index
consists of eight index
notches located on
the front/right of the
console. Each notch
corresponds to a 1⁄2”
change in the deck
height position ranging
from 1-1⁄2” at the lowest
notch to 4” at the highest
notch.
Deck Lift Handle (C)
The deck lift handle is
located on the front/right
of the console, and is used
to raise and lower the
mower deck.
Pull the deck lift handle to the left out of the index
notch and push downward to lower the deck, or pull
upward to raise the deck. When the desired height is
attained, move the deck lift handle to the right until
fully in the index notch.
Ignition Module (D)
WARNING
Never leave a running machine unattended. Always
disengage PTO, set parking brake, stop engine and remove
key to prevent unintended starting.
The ignition module is located on the left fender of
the riding mower seated in the operator’s position,
adjacent to the throttle/choke control or throttle
control.
Ignition Module w/ Reverse Caution Mode (If
equipped)
To start the
engine, insert
the key into
the ignition
switch and turn
clockwise to
the START
position. Release
the key into
the NORMAL
MOWING MODE
position
once the engine
has fired.
To stop the engine, turn the ignition key
counterclockwise to the STOP
position.
CAUTION
Prior to operating the riding mower, refer to both Safety
Interlock Switches and Starting The Engine in the Operation
section of this manual for detailed instructions regarding
the Ignition Switch Module and operating the riding mower
in REVERSE CAUTION MODE
.
Ignition Module (If equipped)
The ignition switch has three
positions:
STOP — The engine and
electrical system is turned off.
RUN — The riding mower
electrical system is energized.
START — The starter motor will turn over the
engine. Release the key immediately when the
engine starts
Note: To prevent accidental starting and/or battery
discharge, remove the key from the ignition switch
when the riding mower is not in use.
Power Take-Off (PTO) Switch (E)
The PTO switch is located on
the RH console.
The PTO switch operates the
electric PTO clutch mounted
on the bottom of the engine
crankshaft. Pull the switch
knob upward to engage the
PTO clutch, or push the knob
downward to disengage the
clutch.
The PTO switch must be in the
“OFF” position when starting
the engine.
Transmission Bypass Rods (F)
The transmission bypass rods (one for each the RH
and LH transmission) are located on the rear of the
tractor, just inside each rear wheel.
When engaged, the two rods open a bypass within
the hydrostatic transmissions, which allows the
tractor to be pushed short distances by hand. Refer
to the Assembly & Set-Up section for instructions
on using the bypass feature.
CAUTION
Never tow your tractor. Towing the tractor with the rear
wheels on the ground may cause severe damage to the
transmissions.
Cup Holder (G)
The cup holder is located toward the middle of the
RH console.
Storage Tray (H)
The storage tray is located at the rear of the RH
console.
Seat Adjustment Lever (I)
The seat adjustment lever is located under
the seat. The seat adjustment lever allows for
adjustment forward or backward of the operator’s
seat. Refer to the Assembly & Set-Up section for
instructions on adjusting the seat position.