manualshive.com logo in svg

Trocen TC-6832, Operation Manual

Share
Download
Trocen TC-6832 Operation Manual Download Page 24

                                                                                                             

WWW.AWC608.COM 

 

Please connect the  corresponding  device 

actual needs. The high and low levels of the input port can be set. It 
is recommended to connect the input signal (the effective signal is 
low  level,  and  the  input  port  is  high  level  24V  in  standby).  The 
signal is the driver alarm si

 

5: output connection

Please  combine  the  definition  of  the  output  port  diagram  and 

connect to the corresponding output port. All the output ports are 
24V  high  levels  during  working  and  0V  while  standby.    All  OUT 
ports  must  be  isolated  by  relays  to  con
cannot be directly connected to OUT ports!

 
The main OUT port is for vibration, suction and punching of the 

cutter head, please install it according to your actual needs.

 

6. Installation of power supply

The  power  supply  of  this 

reliable switching power supply, DC 24V 3A switching power supply 
is recommended 

 

7: Connection of system communication

This  system  supports  network  and  USB  communication.  Please 

use the network cable and USB cable confi
connect the computer, especially no extention for the USB cable.

 

8: software installation

                                                                                                             

Motion controller user manual

 

Please connect the  corresponding  device  input  according  to the 

actual needs. The high and low levels of the input port can be set. It 
is recommended to connect the input signal (the effective signal is 
low  level,  and  the  input  port  is  high  level  24V  in  standby).  The 
signal is the driver alarm signal 

5: output connection 

Please  combine  the  definition  of  the  output  port  diagram  and 

connect to the corresponding output port. All the output ports are 
24V  high  levels  during  working  and  0V  while  standby.    All  OUT 
ports  must  be  isolated  by  relays  to  connect  to  peripherals,  and 
cannot be directly connected to OUT ports! 

The main OUT port is for vibration, suction and punching of the 

cutter head, please install it according to your actual needs.

6. Installation of power supply 

The  power  supply  of  this  system  is  DC  24  V,  please  provide  a 

reliable switching power supply, DC 24V 3A switching power supply 

7: Connection of system communication 

This  system  supports  network  and  USB  communication.  Please 

use the network cable and USB cable configured with the system to 
connect the computer, especially no extention for the USB cable.

8: software installation 

                                                                                                              TC-6832   

Motion controller user manual

 

 

23 

input  according  to the 

actual needs. The high and low levels of the input port can be set. It 
is recommended to connect the input signal (the effective signal is 
low  level,  and  the  input  port  is  high  level  24V  in  standby).  The 

Please  combine  the  definition  of  the  output  port  diagram  and 

connect to the corresponding output port. All the output ports are 
24V  high  levels  during  working  and  0V  while  standby.    All  OUT 

nect  to  peripherals,  and 

The main OUT port is for vibration, suction and punching of the 

cutter head, please install it according to your actual needs. 

system  is  DC  24  V,  please  provide  a 

reliable switching power supply, DC 24V 3A switching power supply 

This  system  supports  network  and  USB  communication.  Please 

gured with the system to 

connect the computer, especially no extention for the USB cable. 

Summary of Contents for TC-6832

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands