INPUT
BREAKER
ACC. SLOT
LOAD 1
IN
PHONE / DATA PROTECTION
OUT
EPO
LOAD 2
OUTPUT
RS-232
USB
CAUTION
Risk of electric shock
See top of unit for
cautionary markings
WARNING
CONNECT 48 VDC
BATTERY SYSTEMS ONLY
CONNECTING OTHER
SYSTEMS WILL VOID
WARRANTY
INPUT
BREAKER
ACC. SLOT
LOAD 1
IN
PHONE / DATA PROTECTION
OUT
EPO
LOAD 2
OUTPUT
RS-232
USB
CAUTION
Risk of electric shock
See top of unit for
cautionary markings
WARNING
CONNECT 48 VDC
BATTERY SYSTEMS ONLY
CONNECTING OTHER
SYSTEMS WILL VOID
WARRANTY
Your model may differ.
1
2a
Your model may differ.
INPUT
BREAKER
ACC. SLOT
LOAD 1
IN
PHONE / DATA PROTECTION
OUT
EPO
LOAD 2
OUTPUT
RS-232
USB
CAUTION
Risk of electric shock
See top of unit for
cautionary markings
WARNING
CONNECT 48 VDC
BATTERY SYSTEMS ONLY
CONNECTING OTHER
SYSTEMS WILL VOID
WARRANTY
2b
Your model may differ.
4
Installation
(continued)
2-Post (Telecom) Mounting
If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post
Rackmount Installation Kit (model: 2POSTRMKITWM, sold separately). See Installation Kit
owner’s manual for installation procedure for 2U UPS models.
Connection and Start-Up
Connect a user-supplied power cord
to the UPS input receptacle.
The power cord should have a plug appropriate for
your local site's utility outlets. Plug the cord
directly into a properly grounded, 3-wire, AC outlet
that does not share a circuit with a heavy electrical
load (air conditioner, refrigerator, etc.). The outlet
must have an amp rating equal to or greater than the
input breaker rating of the UPS.
Note: Once your UPS is plugged in, the fan and all Indicator
Lights will turn ON. The LINE and LOAD ACTIVE METER
LEDs will illuminate and the UPS will beep to indicate normal
operation. However, power is not supplied to the AC outlets until
the UPS is turned on.
Using the included power cords,
connect your equipment to the AC
outlets of the UPS System.
Connect the female plug to your equipment's
AC input. Connect the male plug to any UPS AC
outlet
2a
. Repeat with additional cords to connect
all your equipment
2b
.
Note: Additional interconnection cords C13 to C14 and C19 to
C20) are available from Tripp Lite. For more information, call
773-869-1234.
Caution: Your UPS is designed to support computer equipment
only. You will overload the UPS if you connect devices with high
power demands such as household appliances or laser printers to
UPS AC outlets.
1
2
Mounting (Tower)
Your UPS can be mounted in an upright tower position
with optional base stands sold separately by Tripp Lite
(Model # 2-9USTAND). When mounting the UPS on
adjustable base stands, make sure that the control panel
is toward the top. The control panel may be rotated to
make it easier to read. Insert a small screwdriver or
similar tool in the slots on either side of the panel, pop
it out, rotate it, and pop it back into place as shown.
WARNING!
All UPS systems are extremely heavy. Use caution when lifting and mounting. User must
properly stabilize the UPS when lifting and mounting.
201203257 93-2486.indd 4
4/3/2012 3:12:56 PM
Summary of Contents for SmartOnline AGPS5546
