Trinamic TMCM-1021 TMCL Manual Download Page 76

Page: 76 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

76 / 109

Axis Parameters

Most motor controller features of the TMCM-1021 module are controlled by axis parameters.

Axis

parameters can be modiﬁed or read using SAP, GAP and AAP commands. Some axis parameters can also

be stored to or restored from the EEPROM using STAP and RSAP commands. This chapter describes all

axis parameters that can be used on the TMCM-1021 module.

Meaning of the Letters in the Access Column

Access type

Command

Description

GAP

Parameter readable

SAP, AAP

Parameter writable

STAP, RSAP

Parameter can be stored in the EEPROM

Table 14: Meaning of the Letters in the Access Column

All Axis Parameters of the TMCM-1021 Module

Number

Axis Parameter

Description

Range [Units]

Access

Target position

The desired target position in position mode

-2147483648

. . . 2147483647

[µsteps]

Actual position

The actual position of the motor. Stop the motor

before overwriting it. Should normally only be

overwritten for reference position setting.

-2147483648

. . . 2147483647

[µsteps]

Target speed

The desired speed in velocity mode. Not valid in

position mode.

-2147483648

. . .

2147483647

[pps]

Actual speed

The actual speed of the motor.

-2147483648

. . .

2147483647

[pps]

Maximum

positioning

speed

The maximum speed used for positioning

ramps.

1. . .

2147483647

[pps]

RWE

Maximum

acceleration

Maximum acceleration during ramp-up.

1. . .

2147483647

[pps

]

RWE

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Summary of Contents for TMCM-1021 TMCL














































































































Search results

Summary of Contents for TMCM-1021 TMCL

Reviews:

Related manuals for TMCM-1021 TMCL

Brands by name

Popular brands

Trinamic TMCM-1021 TMCL, Manual

Search results

Summary of Contents for TMCM-1021 TMCL

Reviews:

Related manuals for TMCM-1021 TMCL

Brands by name

Popular brands