Trinamic TMCM-1021 TMCL Manual Download Page 2

Page: 2 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

2 / 109

Contents

Features

1.1

stallGuard2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2

coolStep

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

First Steps with TMCL

2.1

Basic Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2

Using the TMCL Direct Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3

Changing Axis Parameters

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4

Testing with a simple TMCL Program

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TMCL and the TMCL-IDE — An Introduction

3.1

Binary Command Format

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1.1

Checksum Calculation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

Reply Format

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2.1

Status Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3

Standalone Applications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4

The ASCII Interface

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4.1

Entering and leaving the ASCII Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4.2

Format of the Command Line

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4.3

Format of a Reply

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4.4

Conﬁguring the ASCII Interface

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5

TMCL Command Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.1

TMCL Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6

TMCL Commands by Subject

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.1

Motion Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.2

Parameter Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.3

Branch Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.4

I/O Port Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.5

Calculation Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.6

Interrupt Processing Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7

Detailed TMCL Command Descriptions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.1

ROR (Rotate Right)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.2

ROL (Rotate Left)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.3

MST (Motor Stop)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.4

MVP (Move to Position)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.5

SAP (Set Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.6

GAP (Get Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.7

STAP (Store Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.8

RSAP (Restore Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.9

SGP (Set Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.10 GGP (Get Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.11 STGP (Store Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.12 RSGP (Restore Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.13 RFS (Reference Search)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.14 SIO (Set Output)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.15 GIO (Get Input)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.16 CALC (Calculate)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.17 COMP (Compare)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.18 JC ( Jump conditional)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.19 JA ( Jump always)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.20 CSUB (Call Subroutine)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7.21 RSUB (Return from Subroutine)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Summary of Contents for TMCM-1021 TMCL














































































































Search results

Summary of Contents for TMCM-1021 TMCL

Reviews:

Related manuals for TMCM-1021 TMCL

Brands by name

Popular brands

Trinamic TMCM-1021 TMCL, Manual

Search results

Summary of Contents for TMCM-1021 TMCL

Reviews:

Related manuals for TMCM-1021 TMCL

Brands by name

Popular brands