Traub TNX42 Operating Instructions Manual Download Page 3

Page: 3 / 64

22.10.2021

TNX65/42

Table of contents

Safety ................................................................................................................................................

................................................................................................................................................ 7

Symbols ............................................................................................................................................. 7
Documentation safety instructions .................................................................................................... 7

Installation and layout diagrams

Installation and layout diagrams ...................................................................................................

................................................................................................... 9

Foundation diagram  ........................................................................................................................... 9
Layout diagram  .................................................................................................................................. 10
Installation diagram  ............................................................................................................................ 11

General data

General data .....................................................................................................................................

..................................................................................................................................... 13

Dimensions (without additional attachments) ................................................................................... 13

TNX65/42 / TNX65/42 with milling unit .......................................................................................... 13

Machine weight and machine dimensions ........................................................................................ 13

TNX65/42  ....................................................................................................................................... 13
TNX65/42 with milling unit  ............................................................................................................ 14
Bearing points*  ............................................................................................................................. 14

Preparing to transport a machine without milling unit

Preparing to transport a machine without milling unit ...............................................................

............................................................... 19

Summary of Contents for TNX42

































































Search results

Summary of Contents for TNX42

Reviews:

Related manuals for TNX42

Brands by name

Popular brands

Traub TNX42, Operating Instructions Manual

Search results

Summary of Contents for TNX42

Reviews:

Related manuals for TNX42

Brands by name

Popular brands