background image

RLC-SVU01B-E4

Foreword

These Installation, Operation, and
Maintenance instructions are given
as a guide to good practice in the
installation, start-up, operation, and
periodic maintenance by the user of
Tracer CH.530 chiller control
modules.

They do not contain the full service
procedures necessary for the
continued successful operation of
this equipment. The services of a
qualified service technician should
be employed, through the medium
of a maintenance contract with a
reputable service company.

Warranty

Warranty is based on the general
terms and conditions of the
constructor. The warranty is void if
the equipment is modified or
repaired without the written approval
of the constructor, if the operating
limits are exceeded, or if the control
system or the electrical wiring is
modified.

Damage due to misuse, lack of
maintenance, or failure to comply
with the manufacturer's instructions,
is not covered by the warranty
obligation.

If the user does not conform to the
rules of chapter "Maintenance," it
may entail cancellation of warranty
and liabilities by the constructor.

Reception

On arrival, inspect the unit before
signing the delivery note. Specify
any damage on the delivery note,
and send a registered letter of
protest to the last carrier of the
goods within 72 hours of delivery.
Notify the local sales office at the
same time.

The unit should be totally inspected
within 7 days of delivery. If any
concealed damage is discovered,
send a registered letter of protest to
the carrier within 7 days of delivery
and notify the local sales office.

Units are shipped with the
refrigerant operating or holding
charge and should be examined with
an electronic leak detector to
determine the hermetic integrity of
the unit. The refrigerant charge is not
included in the standard Warranty
Cover.

General information

About this manual

Cautions appear at appropriate
places in this instruction manual.
Your personal safety and the proper
operation of this machine require
that you follow them carefully.

The constructor assumes no liability
for installations or servicing
performed by unqualified personnel.

©American Standard Inc. 2004

Summary of Contents for Tracer CH.530 RLC-SVU01B-E4





























































Reviews: