Trane TC*150-301 Installation Operation & Maintenance Download Page 54

Page: 54 / 64

RT-SVX25C-EN

Troubleshooting

4. Locate the RTRM (J6). Connect two (2) wires to terminals J6-1 and 2.

5. Connect the sensor (OAS) using two wire nuts to the two (2) field supplied wires that were

connected to terminals 1 and 2 on J6.

Unit Economizer Control (ECA) Troubleshooting ReliaTel Control

Verify Economizer Status by Economizer Actuator (ECA) LED indicator:

•

OFF: No Power or Failure

•

ON: Normal, OK to Economize

•

Slow Flash: Normal, Not OK to Economize

•

Fast Flash - 1/4 Second On / 2 Seconds Off:

–

Error Code: Communications Failure

•

Pulse Flash: 1/30 Second On / 1/4 Second Off: (2 Seconds between pulse sequences)

Error Code:

•

1 Flash: Actuator Fault

•

2 Flashes: CO2 Sensor

•

3 Flashes: RA Humidity Sensor

•

4 Flashes: RA Temp Sensor

•

5 Flashes: OA Quality Sensor

•

6 Flashes: OA Humidity Sensor

•

7 Flashes: OA Temp Sensor

•

8 Flashes: MA Temp Sensor

•

9 Flashes: RAM Fault

•

10 Flashes: ROM Fault

•

11 Flashes: EEPROM Fault

Summary of Contents for TC*150-301

































































Search results

Summary of Contents for TC*150-301

Reviews:

Related manuals for TC*150-301

Brands by name

Popular brands

Trane TC*150-301, Installation Operation & Maintenance

Search results

Summary of Contents for TC*150-301

Reviews:

Related manuals for TC*150-301

Brands by name

Popular brands