manualshive.com logo in svg

Trane TC*150-301, Installation Operation & Maintenance, Page: 29 / 64

Share
Download
Trane TC*150-301 Installation Operation & Maintenance Download Page 29

RT-SVX25C-EN

29

Installation

Smoke Detector

Customer Low Voltage Wiring-

When interlocking System Sensor smoke detectors together, all of the detectors must be powered 
from the same power supply. If multiple smoke detectors are required, all detectors must be 
disconnected from the HVAC unit power supply and connected together from another single 
source supply.

Note:

Do not interconnect smoke detectors together that have separate power supplies. Do not 
exceed ten smoke detectors on one power supply.

Note:

Multiple System Sensor smoke detectors are connected together using terminals 1 and 12 
on each detector.

–

If you have supply and return smoke detectors in all HVAC units, you can connect a 
maximum of 5 HVAC units (10 detectors) up to one power supply.

See the following field wiring example.

–

If you have more than 5 HVAC units, you can connect all the supplies together on one power 
supply (up to 10 HVAC units), and all the returns together (up to 10 HVAC units) on another 
power supply. 

See the following field wiring example.

Figure 16. ReliaTel humidistat (dehumidification option)

Summary of Contents for TC*150-301

































































Reviews:

No comments