Trane TC*150-301 Installation Operation & Maintenance Download Page 57

Page: 57 / 64

RT-SVX25C-EN

Wiring Diagrams

2309-3366

Connection Electrical - 400 - 575v (TC 151 - With Dehumidification Option)

2309-3367

Connection Electrical - 208 - 230v - Cooling / Gas Heat (YC 151 With Dehumidication Option)

2309-3368

Connection Electrical - 400 - 575v - Cooling / Gas Heat (YC 151- With Dehumidification Option)

2309-3369

Connection Electrical - 208 - 230v (TC 181-With Dehumidification Option)

2309-3370

Connection Electrical - 400 - 575v (TC 181 - With Dehumidification Option)

2309-3371

Connection Electrical - 208 - 230v - Cooling / Gas Heat (YC 181 With Dehumidification Option)

2309-3372

Connection Electrical - 400 - 575v - Cooling / Gas Heat (YC 181- With Dehumidification Option)

2309-3373

Connection Electrical - 208 - 230v (TC 241-With Dehumidification Option)

2309-3374

Connection Electrical - 400 - 575v (TC 241 With Dehumidification Option)

2309-3375

Connection Electrical - 208 - 230v - Cooling / Gas Heat (YC 241 With Dehumidification Option)

2309-3376

Connection Electrical - 400 - 575v -Cooling / Gas Heat (YC 241- With Dehumidification Option)

2309-3377

MASTER DRAWING; CONNECTION DIAGRAMS--VOY2

2309-3378

Electrical Schematic - 400-575v - Power Reliatel (YC 151)

2309-3379

Electrical Schematic - 208 - 230v - Power Reliatel (YC 151)

2309-3380

Electrical Schematic - 208-230v - Power Reliatel (TC 151)

2309-3381

Electrical Schematic - 400 - 575v - Power Reliatel (TC 151)

2309-3382

Electrical Schematic - 208 - 230v - Power Reliatel (WC 150, 240)

2309-3383

Electrical Schematic - 400 - 575v - Power Reliatel (WC 150, 240)

2309-3384

Electrical Schematic - 380v - Power Reliatel (YC 150, 210, 240, 300)

2309-3385

Electrical Schematic - 380v - Power Reliatel (TC 150, 210, 240, 300)

2309-3386

Electrical Schematic - 400-575v - Power Reliatel (YC 150, 155, 175, 180, 210, 211)

2309-3387

Electrical Schematic - 208 - 230v - Power Reliatel (YC150, 180, 181, 210, 211)

2309-3388

Electrical Schematic - 208-230v - Power Reliatel (TC 150, 180, 181, 210, 211)

2309-3389

Electrical Schematic-400-575v -Power Reliatel (TC 150, 155, 175, 180, 181, 210, 211)

2309-3390

Schematic Electrical - 200, 208 - 575v - Control - Micro Processor (YC 150 - 301)

2309-3391

Schematic Electrical - 200, 208 - 575v - Control - Micro Processor (TC 150 - 301)

2309-3392

Schematic Electrical - 200, 208 - 575v - Control - Micro Processor (WC 150 - 240)

2309-3393

Connection Electrical - 208 - 230v (WC 150)

2309-3394

Connection Electrical - 208 - 230v (WC 150)

2309-3395

Connection Electrical - 208 - 230v - Cooling / Gas Heat (YC 151)

2309-3396

Connection Electrical - 400-575v - Cooling / Gas Heat (YC 151)

2309-3397

Connection Electrical - 208 - 230v (TC 151)

2309-3398

Connection Electrical - 400 - 575v (TC 151)

2309-3399

Connection Electrical - 208 - 230v (TC 150)

2309-3400

Connection Electrical - 400 - 575v (TC 150)

2309-3401

Diagram, Connection 380V TC 150

2309-3402

Connection Electrical - 380v - Cooling / Gas Heat (YC 150)

2309-3802

Diagram, Connection Electrical TC 240E 208/230V

2309-3803

Diagram, Connect on Electrical TC 240E 460-575V

Table 13. Wiring diagrams for R-22 units and heaters (continued)

Drawing
Number

Description

Summary of Contents for TC*150-301

































































Search results

Summary of Contents for TC*150-301

Reviews:

Related manuals for TC*150-301

Brands by name

Popular brands

Trane TC*150-301, Installation Operation & Maintenance

Search results

Summary of Contents for TC*150-301

Reviews:

Related manuals for TC*150-301

Brands by name

Popular brands