background image

Literature Change History

GPND-IN-1 (August 1997)

Original issue of the manual.

Warnings and Cautions

Warnings and Cautions appear at
appropriate sections throughout
this manual.

WARNINGS!

alert the installer, owner,
operator or service personnel
to potential hazards which if
not avoided could result in
death or serious personal injury.

Cautions:

alert personnel to conditions
which if not avoided may result
in minor or moderate injury.
Also alerts against unsafe prac-
tices causing equipment
damage.

Shipping Instructions

Before installing the nozzle kit, be
sure to confirm that the proper kit
has been sipped.

If a thorough inspection of the kit
reveals damage or material
shortages, file a claim with the
carrier immediately. Specify the
extent and type of damage found,
and notify the appropriate Trane
sales office. Do not install a
damaged nozzle kit without the
Trane sales representative’s
approval!

Description

The nozzle kits are used to direct
discharge air on unit heaters with
a variety of angles available.

Table of Contents

General Information . . . . . . . . . . . . . . . . . . .

2

Literature Change History . . . . . . . . . . . . . . . .

2

Warnings and Cautions . . . . . . . . . . . . . . . . .

2

Description . . . . . . . . . . . . . . . . . . . . . . . .

2

Installation . . . . . . . . . . . . . . . . . . . . . . . .

3

30° Nozzle Kit . . . . . . . . . . . . . . . . . . . . . .

3

45° Nozzle Kit . . . . . . . . . . . . . . . . . . . . . .

4

60° Nozzle Kit . . . . . . . . . . . . . . . . . . . . . .

5

90° Nozzle Kit . . . . . . . . . . . . . . . . . . . . . .

6

5-Way Blow Down Nozzle Kit . . . . . . . . . . . . . .

7

Y-Splitter Nozzle Kit . . . . . . . . . . . . . . . . . . .

7

General Information

2

GPND-IN-1

Summary of Contents for GBPD








Reviews: