background image

WARNING!

Disconnect the power source
before installing this kit to
prevent death or serious
personal injury due to
electrical shock.

For Use On Propeller and
Blower Unit Heaters
Natural or Power Vent

Recommended procedure for the
nozzle installation to the unit
heater:

1. Standard (Natural Vent)

Units

1. Remove the louvers and cone

springs from the discharge
end of the unit heater.

2. Remove the upper front trim

panel (located directly above
the heat exchanger opening).

3. Install the nozzle by simply

hooking the top panel flange
of the nozzle over the top
flange of the heat exchanger.
The nozzle side panels should
slide inside the heat
exchanger opening.

4. Secure the bottom of the

nozzle to the lower front trim
panel of the unit heater, by
drilling through and using the
screws provided.

2. High Efficiency (Power Vent)

Units

1. Remove the louvers and cone

springs from the discharge
end of the unit heater

2. Remove the screws from the

upper front trim panel of the
unit heater.

3. Install the nozzle by securing

the top panel of the nozzle to
the face of the upper front trim
panel, using the screws that
were just removed from each
end. The sides of the nozzle
should slide into the heat
exchanger opening.

4. Add the remaining screws in

the locations provided in the
nozzle top panel; drill through
into the unit heater trim panel.

5. Secure the bottom of the

nozzle to the lower front trim
panel of the unit heater, by
drilling through and using the
screws provided.

Installation—90° Nozzle Kit

6

GPND-IN-1

Summary of Contents for GBPD








Reviews: