manualshive.com logo in svg

Trafox SUPERINTEND IC-01, Instructions For Installation And Use Manual, Page: 71 / 73

Share
Download
Trafox SUPERINTEND IC-01 Instructions For Installation And Use Manual Download Page 71

Superintend IMD

 

© Copyright Muuntosähkö Oy - Trafox

 

 

71 

 

http://www.trafox.fi

 

QUICK INSTRUCTION TEMPLATES OF IC-01 AND 
TC-01 FOR MEDICAL LOCATIONS 

 

 

 

 

 

The device indicates the insulation level of 
the IT network. When all is fine, the OK 

indicator is lit. 

If either INSULATION indicator blinks, a low 
insulation level alarm is active. If this is the 
case, disconnect devices from wall sockets, 
starting from the one added last, until the 

INSULATION indicators no longer blink. 

The PE FAULT indicator means there is an 

earthing break in the wall socket. 

The SYSTEM FAULT indicator means a 

disturbance in IC-01. 

In the case of any alarm: silence the audible alarm with 

the MUTE ALARM button and notify 

__________________________ tel. _________________ 

The device indicates the load level and 
temperature of the IT network isolation 
transformer. When all is fine, the OK 
indicator is lit. 

If either ALARM indicator blinks, the IT 
network is overloaded. If this is the case, 
disconnect devices from wall sockets until the 
ALARM indicators no longer blink. 

The SYSTEM FAULT indicator means a 

disturbance in TC-01. 

Load/temp. indicates the momentary load 

level of the IT network. 

In the case of any alarm: silence the audible alarm with 
the MUTE ALARM button and notify 

__________________________ tel. _________________ 

Summary of Contents for SUPERINTEND IC-01










































































Reviews:

No comments