manualshive.com logo in svg

Trafox SUPERINTEND IC-01, Instructions For Installation And Use Manual, Page: 29 / 73

Share
Download
Trafox SUPERINTEND IC-01 Instructions For Installation And Use Manual Download Page 29

Superintend IMD

 

© Copyright Muuntosähkö Oy - Trafox

 

 

29 

 

http://www.trafox.fi

 

The following parameters can be changed in the Setup menu: 

 

INSULATION LIMIT

: Alarm limit of the insulation resistance.  If the measured 

value is lower than the alarm limit, an alarm is given.  The setup range is 50 
kΩ…1,000 kΩ. It can be set at 50 kΩ intervals. 

 

PRE INSULATION LIMIT: 

The pre-insulation limit of the insulation resistance.

  

Given as a percentage of the insulation limit.  Activates the AUX. ALARM relay, 
unless it is removed from the AUX alarm mask. The setup range is 100…200%, at 
10% intervals.  

 

TEMPERATURE LIMIT:

 The alarm limit of the transformer temperature. Can be 

set between 30…140 °C or switched OFF if temperature measurement is not 
used.

 

 

TEMPERATURE SENSOR TYPE:

 The type of the temperature sensor used (NTC 

or PT100).

 

 

PT100 CALIBRATION:

 This setting is only used when PT100 is selected as the 

temperature sensor. It can compensate for the error caused by long 
measurement wires (the maximum loop resistance is 20 Ω) in the temperature 
value. A 130 Ω resistor is connected to the end of the measurement wires in the 
place of the PT100 sensor, after which calibration is performed:

 

 

If the resistance measured in calibration is too low or too high, the message 
displayed is Failed, instead of Cal.OK. In that situation, check the connection. 

 

LOAD LIMIT:

 The current limit of the transformer as a percentage of the 

transformer's nominal current.  Can be set between 50…140% or switched OFF if 
load current measurement is not used. 

 

TRAN SIZE:

 The nominal value of the current transformer. The primary current 

that provides a current transformer output current of 5A. The setup range is 10–
100 A. 

 

NOMINAL CURRENT:

 The nominal current of the isolation transformer at full 

power. SETUP RANGE 1–100 A. 

Summary of Contents for SUPERINTEND IC-01










































































Reviews:

No comments