manualshive.com logo in svg

Trafox SUPERINTEND IC-01, Instructions For Installation And Use Manual, Page: 59 / 73

Share
Download
Trafox SUPERINTEND IC-01 Instructions For Installation And Use Manual Download Page 59

Superintend IMD

 

© Copyright Muuntosähkö Oy - Trafox

 

 

59 

 

http://www.trafox.fi

 

Alarm mode 

The alarm mode can be accessed through the monitor mode by pressing the 
MON/ALARM button. In the alarm mode, the screen displays all active alarms and 
removed alarms, which have not been acknowledged. The active alarms are displayed 
first and after that the removed alarms, which have not been acknowledged. You can 

move down the alarm list by pressing the 

 button. The display modes in the alarm 

mode can, for example, be as follows (in the parallel display pictures, the lower line of 
the text switches between the two examples automatically every 2 seconds): 

 

Insulation resistance alarm. The upper line 
displays the lowest insulation resistance measured 
during the fault / alarm limit. 

Insulation resistance pre-alarm. The upper line 
displays the momentary insulation resistance / 
pre-alarm limit. 

Temperature alarm. The upper line displays the 
momentary temperature / alarm limit. 

 

Load current alarm. The upper line displays the 
momentary load current / alarm limit. 

 

 

PE wire alarm, in which the address of the PEC-01 
that caused the alarm (disconnected channel or 
broken connection) is displayed. 

There are no active alarms in the system. 

 

 

Additionally, the following upper line alarm texts are possible: 

 

Sys Test 

System test alarm 

 

Gnd Fail 

Gnd Fail alarm (disconnected TG or MG wire) 

 

M1M2Fail 

WireAmpl or WireOffs alarm (disconnected M1 or  
M2 wire, or short-circuited insulation resistance) 

 

Noise 

Noise alarm 

 

T-sens 0 

Alarm caused by disconnected temperature sensor  
measurement wire 

 

T-sens S 

Alarm caused by short circuited temperature sensor  

180/300k 

Insulat.

 

400/450k 

PreInsul

 

145/105C 

Temp Lim

 

180/300k 

 ALARM

 

400/450k 

WARNING

 

145/105C 

 ALARM

 

 39/ 36A 

Load Lim

 

 39/ 36A 

 ALARM

 

  PE 3 

 ALARM

 

 NO

 

 ALARMS 

Summary of Contents for SUPERINTEND IC-01










































































Reviews:

No comments