Trafox SUPERINTEND IC-01 Instructions For Installation And Use Manual Download Page 39

Page: 39 / 73

Superintend IMD

http://www.trafox.fi

ERRORS

The following table lists the functioning of the IM-01.MED, IC-01, TC-01, RD-01 and
PEC-01 units in various error situations.

Error

IM-01.MED
ALARM
LEDs

IM-01.MED
ALARM
menu

IC-01

TC-01

RD-01 PEC-01 Alarm

relay

PEC-01 unit is missing

REMOTE UNITS

InstUnit

WireFaul

PE FAULT

ALARM

SYSTEM
FAIL (1)

AUX*

The IM-01.MED is not

communicating with any

device (2)

REMOTE UNITS

WIRE FAULT

InstUnit

WireFaul

SYSTEM

FAULT

SYSTEM

FAULT

SYSTEM

FAULT

SYSTEM

FAIL

AUX*

The IM-01.MED unit

without operating voltage

SYSTEM

FAIL

INS AUX TRF

The IC-01/TC-01 remote

display is missing

REMOTE UNITS

InstUnit

SYSTEM

FAULT(3)

SYSTEM

FAULT(3)

SYSTEM

FAULT (3)

AUX*

Memory fault (microSD

card)

MEMORY FAULT

Memory

AUX*

Overload

LOAD

Load Lim

OVERLOAD

ALARM

TRF

Over temperature

TEMPERATURE

Temp Lim

OVERTEMP.

ALARM

TRF

Insulation fault (R under

InsLimit)

INSULATION

Insulat.

INSULATION

FAULT

ALARM

INS

Insulation fault (R under

PrInsLim)

INSULATION

PreInsul

INSULATION

WARNING

AUX*

PE fault (a break in the

channel of the PEC-01

remote unit or resistance

exceeds the alarm limit)

WIRE FAULT

WireFaul

PE FAULT

ALARM

FAIL

AUX*

Incorrect time

ClockErr

AUX*

The IM-01.MED unit TG
wire is disconnected

INSULATION

Gnd Fail

INSULATION
FAULT

ALARM

INS

The IM-01.MED unit MG
wire is disconnected

INSULATION

Gnd Fail

INSULATION
FAULT

ALARM

INS

The IM-01.MED unit M1

wire is disconnected

INSULATION(4)

WireAmpl

WireOffs

INSULATION

FAULT

ALARM

INS(4)

The IM-01.MED unit M2

wire is disconnected

INSULATION(4)

WireOffs

INSULATION

FAULT

ALARM

INS(4)

IM-01.MED is not capable

of measuring insulation

resistance and

capacitance

INSULATION(5)

MeasFail(5)

INSULATION

FAULT

ALARM

INS(5)

System fault (manual

test)

INSULATION

Sys Test

INSULATION

FAULT

ALARM

INS

Summary of Contents for SUPERINTEND IC-01










































































Search results

Summary of Contents for SUPERINTEND IC-01

Reviews:

Trafox SUPERINTEND IC-01, Instructions For Installation And Use Manual, Page: 39 / 73

Search results

Summary of Contents for SUPERINTEND IC-01

Reviews: