manualshive.com logo in svg

Trafox SUPERINTEND IC-01, Instructions For Installation And Use Manual, Page: 44 / 73

Share
Download
Trafox SUPERINTEND IC-01 Instructions For Installation And Use Manual Download Page 44

44

 

© Copyright Muuntosähkö Oy – Trafox

 

Superintend IMD 

 

http://www.trafox.fi

 

again or has been removed. 

Missing TC Acknowledge [TC

XX

] 

Identification or removal of the 
TC-01 unit from the TC 
address 

XX 

was acknowledged 

manually. 

TC Unit Removed [TC

XX

] 

The TC-01 unit configured to 
TC address

 X

X has been 

removed from the network.  

TC Unit Added [TC

XX

] 

The TC-01 unit has been added 
to TC address 

XX

. 

Missing IC Alarm ON [IC

XX

] 

The IC-01 unit configured in 
the IC address 

XX 

is not 

responding. 

Missing IC Alarm OFF [IC

XX

] 

The IC-01 unit configured in IC 
address 

XX 

 is responding 

again or has been removed. 

Missing IC Acknowledge [IC

XX

] 

Identification or removal of the 
IC-01 unit from the IC address 

XX 

was acknowledged 

manually. 

IC Unit Removed [IC

XX

] 

The IC-01 unit configured to IC 
address

 X

X has been removed 

from the network.  

IC Unit Added [IC

XX

] 

The IC-01 unit has been added 
to IC address 

XX

. 

Missing RD Alarm ON [RDXX] 

The RD-01 unit configured in 
the RD address 

XX 

is not 

responding. 

Missing RD Alarm OFF [RDXX] 

The RD-01 unit configured in 
RD address 

XX

 is responding 

again or has been removed. 

Missing RD Acknowledge [RD

XX

] 

Identification or removal of the 
RD-01 unit from the RD 
address 

XX 

was acknowledged 

manually. 

RD Unit Removed [RD

XX

] 

The RD-01 unit configured to 
RD address

 X

X has been 

removed from the network. 

RD Unit Added [RD

XX

] 

The RD-01 unit has been 
added to RD address 

XX

. 

Missing PE Alarm ON [PE

XX

] 

The PEC-01 unit configured in 
the PE address 

XX 

is not 

responding. 

Missing PE Alarm OFF [PE

XX

] 

The PEC-01 unit configured in 
PE address 

XX 

 is responding 

again or has been removed. 

Missing PE Acknowledge [PE

XX

] 

Identification or removal of the 
PEC-01 unit from the PE 
address 

XX 

was acknowledged 

manually. 

Missing PE Channel Alarm ON [PE

XX

 CH

CC

] 

The channel 

CC 

of the PEC-01 

unit configured in PE address 

XX

 has been disconnected. 

Missing PE Channel Alarm OFF [PE

XX

 CH

CC

] 

The channel 

CC 

of the PEC-01 

unit configured in PE address 

XX

 has been restored from an 

Summary of Contents for SUPERINTEND IC-01










































































Reviews:

No comments