manualshive.com logo in svg

Trafox SUPERINTEND IC-01, Instructions For Installation And Use Manual, Page: 58 / 73

Share
Download
Trafox SUPERINTEND IC-01 Instructions For Installation And Use Manual Download Page 58

58

 

© Copyright Muuntosähkö Oy – Trafox

 

Superintend IMD 

 

http://www.trafox.fi

 

earthing wire resistance measured by any PEC-01 unit exceeds the limit provided, 
or if there is a break in the wire. The alarm is deactivated and the LED is on 
steadily when all the above-mentioned values have returned to 5% below the 
alarm limit. The alarm limit is set in the SETUP menu. 

 

The SYSTEM FAULT LED blinks if the system has not received a command from 
the IM-01.MED unit within three seconds. The screen also goes into System Fault 
mode. The alarm is deactivated if the connection is restored. The error is always 
unit-specific; in other words, it is only displayed in the affected unit. In the IM-
01.MED unit, the error is displayed as a REMOTE UNITS error. 

 

The MON/ALARM button changes the screen mode between monitor and alarm 
modes. 

 

The MUTE ALARM button silences the audible alarm. It does not have any other 
effect on the functioning of the system as a whole.  

 

A short press of the 

 button changes the value displayed on the bottom line of 

the display. A long press of the button (5 s) gives the IM-01.MED unit the 
command to perform a system test. 

The RD-01 unit has two screen modes: monitor and alarm. In addition, the system test 
mode and setup mode are accessed through the monitor mode. 

 

Monitor mode 

In the monitor mode, the unit always displays the insulation resistance value on the 
upper line. Additionally, it displays the transformer load current, transformer 
temperature or insulation capacitance on the lower line. The value displayed on the 

lower line can be changed by shortly pressing the 

 button. 

 

R  472k

Ω

 

I    44%

 

R  472k

Ω

 

t  30 °C

 

R  472k

Ω

 

C  0.2uF

 

Summary of Contents for SUPERINTEND IC-01










































































Reviews:

No comments