background image

Söllnerstr. 9 92637 Weiden

[email protected]

+49 (0)961 48 23 0 0

S7-USB user manual

67 / 85

2019/10/05 05:07

The Access over a telephone-line on the PLC could be configured in this dialog.

The Administrator could change the configuration over a telephone line, where an 2 User could not change
the configuration.

The User-Name is maximal 8 Chars long.Every user and the administrator could use a password which is
used to log into the PLC over a telephone-line. These have to enter for each new call.

After 3 wrong retries the connection is hanged up, so you must call again (Not so with an original TS-
adapter).

After changing the password for one user/administrator you must re-type it again correctly before it is
used.

In call-back-number you could define a telephone-number which is used for call-back from the TS-adapter.
After you connect with the TS-adapter, you are asked for your user-name and password. When the correct
password and user-name is transfered, the connection is hanged-up and the TS-adapter is calling back this
configured call-back-number.

GSM/ISDN/SMS

Analog modem:

You could choose the Location of the Modem.

ISDN modem:

Summary of Contents for S7-USB






















































































Reviews: