TPI 712 Manual Download Page 3

Page: 3 / 29

Instrument Overview

Front View

Rubber Boot

Protects the instrument from accidental damage

Display

Large 3 Parameter Backlit LCD Display

Battery Condition Icon

Shows condition of rechargeable batteries.

Keypad

Selects all available functions

Selected Fuel Type

N GAS, LPG, LIGHT OIL, HEAVY OIL, OPT 1
(Bituminous Coal), OPT 2 (Anthracite Coal),
OPT 3 (Coke), OPT 4 (Butane), OPT 5 (Wood),
OPT 6 (Bagasse)

Rubber
Boot

LCD
Display

Keypad

Battery
Condition
Icon

Selected
Fuel Type

General Overview (Continued)

Never over saturate your sensors by performing tests on equipment
with gas levels beyond the capability of you analyzer.

Always keep the A762 water trap / filter assembly clean and replace the
filter as necessary. Replacement filter part number is A762F.

This manual will guide you through the functions of the TPI 712 which
will give you many years of reliable service.

Your TPI 712 Flue Gas Analyzer comes complete with the following
standard accessories:

( ) Denotes part number

•

TPI 712 Analyzer

•

Rubber Boot (A765) 1 each installed on analyzer

•

Soft Carrying Case (A768) - 1 each

•

Flue Sampling Probe (A770) - 1 each

•

In-Line Filter / Water Trap installed on Flue probe (A795) - 1 each

•

Disc water filter installed in water trap (A794W) - 1 each

•

Spare In-Line Filter - 1 each (A794F is a package of 5 filters)

•

Temperature Probe (GK11M) - 1 each

•

Battery Charger (A766) - 1 each

•

Mini Pump Protection Filter Assembly (A763) - 1 each

•

Exhaust Spigot Removable (A764) - 1 each

•

Pressure Tubing (A774) - 1 each 6’ piece

•

Static Pressure Tips (A776) - 2 each

•

1/4” barbed to 1/8” NPT fitting (A603) - 2 each

•

Gas Valve Adapter (A611) - 1 each

•

Adapter Tubing (A791) - 1 each 4” piece

•

Instruction Manual

Your TPI 712 Flue Gas Analyzer has the following options available:

•

A772 PC Software for analysis of Data Logging results

•

A767 Infrared adapter for PC communication

•

A740 infrared printer

(Included with 712A740)

NOTE: When selecting oil as fuel be sure to use the optional

oil filter (A773) or readings could become erratic. See
Appendix E for installation instructions.

Summary of Contents for 712






























Search results

Summary of Contents for 712

Reviews:

Related manuals for 712

Brands by name

Popular brands

TPI 712, Manual

Search results

Summary of Contents for 712

Reviews:

Related manuals for 712

Brands by name

Popular brands