background image

PRINTING DATA (Continued)

Printout Interpretation

Data from combustion
test is printed here.

Smoke Test Result. For
use on oil fired equip-
ment.
(Circle one to indicate
the result of a smoke
test performed using
the optional A788
smoke test pump.)

Date and time of
combustion test.

Fuel type selected
during test.

Customer information
and signed confirmation
of test.
(Fill in this data and
have the customer sign
for confirmation.)

29

PRINTING DATA

WARNING:

- To operate correctly there must be a clear line of sight between

the Infrared Window on the instrument (see page 6) and the Infrared Window
on the IR Printer (see Printer instructions). Place the printer so it is no closer
than approximately 6 inches from the analyzer.

Real Print Mode

- Real print mode enables the analyzer to print the test

data currently on the display (real time data).

Stor Print Mode

- Stor print mode enables the analyzer to print test data

stored in memory.

Titn Print Mode

- Titn print mode enables the analyzer to print tightness

test data stored in memory.

S-Lg Print Mode

- S-Lg print mode enables the analyzer to print data

from a single log test stored in memory.

1. Press the Print/COM Key once. “Real”, “Stor”, and “Titn” will be dis-

played. Pressing the Down Arrow Key repeatedly will cause “Stor”, “Titn”,
and “S-Lg” to be displayed. Use the Up and Down Arrow Keys to select
the desired print mode and press the Scroll/Enter Key. If selecting “Real”
print mode, proceed to step 3. 

To cancel printing press the Print/COM

Key, use the Up/Down Arrow Keys to select “YES” and press the
Scroll/Enter Key.

2. If “Stor”, “Titn”, or “S-Lg” is selected “Addr” and a location number from

0 to 49 (0 to 4 for S-Lg) will flash on the display. Use the Up/Down Arrow
Keys to select the desired location to print data from and press the
Scroll/Enter Key. 

To cancel printing press the Print/COM Key, use the

Up/Down Arrow Keys to select “YES” and press the Scroll/Enter Key.

3. The analyzer will display “Print”, ‘Wait’, ‘out’ and bars will change position

on the LCD until printing is complete.

4. After data transmission is complete “End” will display. Use the Up/Down

Arrow Keys to select “Yes” to stop printing and return to normal opera-
tion or select “No” to print again following steps 1 through 4. Press the
Scroll/Enter Key.

Note: Combustion and pressure/draft printouts must be performed sep-
arately. Perform a combustion test and save the data. Perform a pres-
sure/draft test and save the data in a different address. Print each
address separately.

28

Summary of Contents for 712






























Reviews: