TPG CA-203A, Operating Manual

Page: 21 / 109

Chapter 5 Function parameter
36
7: even parity (E, 7, 1) for ASCII
8: odd parity (O, 7, 1) for ASCII
9: no parity (N, 7, 2) for ASCII
10: even parity (E, 7, 2) for ASCII
11: odd parity (O, 7, 2) for ASCII
12: no parity (N, 8, 1) for ASCII
13: even parity (E, 8, 1) for ASCII
14: odd parity (O, 8, 1) for ASCII
15: no parity (N, 8, 2) for ASCII
16: even parity (E, 8, 2) for ASCII
17: odd parity (O, 8, 2) for ASCII
137. F9.02
Communication
address of this unit
1 to 247, 0 for broadcast address 1
☆
138. F9.03
Communication
response delay
0 to 200ms 5ms
☆
139. F9.04
Communication
timeout fault time 0.0 (Invalid ） ;
0.1 to 100.0s
0.0 s ☆
140. F9.05
Data transfer
format selection
0: non-standard MODBUS
protocol
1: standard MODBUS protocol
2: ASCII
0 ☆
141. F9.06
Transmission error
handling
0: Alarm and free stop
1: No alarm and continue to run
2: No alarm and stop at the
selected mode (under
communication control mode
only)
3: No alarm and stop at the
selected mode (under all control
modes)
1
☆
142. F9.07
Transmission
response handling 0: Write operations responded
1: Write operations not responded
0
☆
5-1-12.FA Group - Torque control
No. Code Parameter name Setting range
Factory
default
Change
143. FA.00
Torque setting
mode selection
0: Keyboard setting (FA.01)
1: Analog AI1 setting
2: Analog AI2 setting
3: Panel potentiometer setting
4: Analog AI1+AI2 setting
5: Multi-segment torque setting
6: Remote communications
0
☆
Chapter 5 Function parameter
37
setting
Note: Option 1 to 6, 100%
relative to two times of the rated
current of inverter
144. FA.01
Keyboard set
torque -200.0% to 200.0% (rated current
of inverter)
50.0%
☆
145. FA.02
low speed torque
compensation
0.000-1.000 0.050 ☆
146. FA.03
high speed torque
compensation
0.000-1.000 0.000
☆
5-1-13.Fb Group - Control optimization
No. Code Parameter name Setting range
Factory
default
Change
147. Fb.00 Software overcurrent point 0 to 2000A
Depends on
models
★
148. Fb.01 Software undervoltage point 0 to 500V
Depends on
models
★
149. Fb.02 Software overvoltage point
300 to 800V
Depends on
models
★
150. Fb.03
Low-frequency threshold point of
oscillation suppression
0 to 500 5
☆
151. Fb.04
High-frequency threshold point of
oscillation suppression
0 to 500 100
☆
152. Fb.05
Amplitude limit value of
oscillation suppression
0 to 10000 5000 ☆
153. Fb.06
Demarcation frequency of high and
low frequency of oscillation
suppression
0.00Hz to F0.08
(maximum
output
frequency)
12.50Hz
☆
154. Fb.07 Oscillation suppression
0: valid 1: invalid 1
☆
155. Fb.08 PWM selection
0: PWM mode 1
1: PWM mode 2
2: PWM mode 3
0
★
156. Fb.09 Energy-saving selection
0: OFF
1. Auto
0 ★
157. Fb.10 Deadband time 2 to 5
Depends on
models
★