TP-Link omada OC200 User Manual Download Page 4

Page: 4 / 117

III

..................................................................................................................94

..................................................................................................................... 95

Configure Daylight Saving Time

............................................................................................................. 97

5.4 Reboot and Reset the EAP

....................................................................................................................99

5.5 Backup and Restore the Configuration

.........................................................................................100

5.6 Update the Firmware

...........................................................................................................................101

6 Application Example

............................................................................................... 102

6.1 Determine the Network Requirements

.........................................................................................103

6.2 Build the Network Topology

..............................................................................................................104

6.3 Log in to the EAP

...................................................................................................................................105

6.4 Configure the EAP

................................................................................................................................106

Configure SSIDs

.........................................................................................................................................106

Configure Portal Authentication

...........................................................................................................107

Configure Scheduler

.................................................................................................................................109

6.5 Test the Network

...................................................................................................................................111

Summary of Contents for omada OC200






















































































































Search results

Summary of Contents for omada OC200

Reviews:

Related manuals for omada OC200

Brands by name

Popular brands

TP-Link omada OC200, User Manual

Search results

Summary of Contents for omada OC200

Reviews:

Related manuals for omada OC200

Brands by name

Popular brands