TP-Link omada OC200 User Manual Download Page 22

Page: 22 / 117

scan all EAPs in the same network segment, and find the IP address of the EAP. In the
following figure, for example, the IP address of the EAP is

192.168.0.5

iipe

Some EAP models only works with certain software version of Discovery Utility. If your Discovery

Utility can’t discover your EAP anyway, try a different software version.

2. To log in to the EAP, launch a web browser and enter the IP address of the EAP in the

address bar. The login page will appear. By default, both the username and password

are

admin

iipe

To facilitate access to the EAP, you can set a static IP address for the EAP and remember it well or

write it down. But make sure that this IP address is not being used by other devices in the same LAN.

For detailed instructions about how to set a static IP address for the EAP, refer to

4.1 Manage the

IP Address of the EAP

Summary of Contents for omada OC200






















































































































Search results

Summary of Contents for omada OC200

Reviews:

Related manuals for omada OC200

Brands by name

Popular brands

TP-Link omada OC200, User Manual

Search results

Summary of Contents for omada OC200

Reviews:

Related manuals for omada OC200

Brands by name

Popular brands