background image

1

READ THROUGH THIS MANUAL

BEFORE STARTING CONSTRUCTION.

IT CONTAINS IMPORTANT INSTRUCTIONS 

AND WARNINGS CONCERNING THE 

ASSEMBLY AND USE OF THIS MODEL.

WEIGHT

60 – 65 oz [1700 – 1842 g]

WING LOADING

20.3 –22.1 oz/ft

2

 [61.9 – 67.4 g/dm

2

]

RADIO

4-Channel required

Tow e r 
Hobbies

®

 

guarantees 
this kit to be 
free from defects 
in  both  material  and 
workmanship at the 
date of purchase. This 
warranty does not cover any 
component parts damaged by 
use or modification. In no case shall 
Tower Hobbies’ liability exceed the 
original cost of the purchased kit. Further, 
Tower Hobbies reserves the right to change 
or modify this warranty without notice.

In that Tower Hobbies has no control over the final 
assembly or material used for final assembly, no 
liability shall be assumed nor accepted for any damage 
resulting from the use by the user of the final user-assembled 
product. By the act of using the user-assembled product, the 
user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the 
use of this product, the buyer is advised to return this kit immediately in 
new and unused condition to the place of purchase.

To make a warranty claim send the defective part or item to Hobby Services at 
the address below:

Hobby Services • 3002 N. Apollo Dr.  Suite 1 • Champaign IL  61822 • USA

Include a letter stating your name, return shipping address, as much contact information as 
possible (daytime telephone number, fax number, e-mail address), a detailed description of 
the problem and a photocopy of the purchase receipt. Upon receipt of the package the problem 
will be evaluated as quickly as possible.

WA

R

R

A

N

TY

TOWA2090

© 

2017 Tower Hobbies.

®

  A subsidiary of Hobbico, Inc. 

®

®

TOWER HOBBIES

Champaign, Illinois

 (217) 398-8970 ext. 6

WINGSPAN

53 in [1346mm]

WING AREA

424 sq in [27.35 dm

2

]

LENGTH

40 in  [1016mm]

[email protected]

INSTRUCTION

MANUAL

Summary of Contents for RYAN STA

























Reviews: