11
Operational Precautions
■
■
For prevention of damage
■
●
Wipe plastic areas such
as the top unit and
remote control with a
soft, wet cloth.
Dry cloth or tissue
■
●
Do not lean against the
toilet lid.
■
■
Problem Prevention
■
●
Disconnect the power plug if there is a risk of lightning.
Switch the breaker on the distribution board to OFF.
(Asia, Oceania, Middle East)
■
●
A toilet seat cover or a toilet lid cover cannot be used.
(The body sensors or seat switch may not function properly.)
Covers
■
●
Do not urinate on the top unit, toilet seat or wand.
(Doing so may cause pink or brown stains or a malfunction.)
■
●
Do not apply strong forces to the control panel of the
remote control.
■
●
When using a toilet cleaner to clean the toilet, wash it off
within 3 minutes and leave the toilet seat and toilet lid open.
Wipe off any cleaner that remains on the toilet bowl.
(If vapor from a toilet bowl cleaner enters the top unit, it may
cause a malfunction.)
■
●
Do not expose to direct sunlight.
(Doing so may cause changes in color, irregular
heated seat temperature, remote control malfunction or
NEOREST malfunction due to the change in temperature.)
■
●
Use radios, etc. away from the NEOREST.
(The NEOREST could cause interference with the radio signal.)
■
●
If you use a booster seat for infants or a soft highchair,
remove it after use.
(Keeping it installed may prevent some of the functions
from being used.)
■
●
Do not apply force to the remote control.
(May cause malfunction.)
To prevent the remote control from being dropped, set it
in the hanger when you are not using it. Be careful not
to expose it to water.
About rear cleansing, rear soft cleansing, front
cleansing and wide front cleansing
●
•
These functions wash away waste and dirt from
a localized area of your body.
●
•
Do not cleanse too much or for too long.
Doing so may wash away normal bacteria, upsetting
the balance of bacteria inside your body.
●
•
People who are receiving medical treatment or
therapy in this localized area should consult
their doctor before use.
■
■
For prevention of malfunctions
■
●
Do not block the body sensor or the remote control transmitter
or receiver.
< About the body sensors >
Two types of body sensors are used.
■
●
Body sensor A detects changes in heat.
●
•
Detection may be difficult when the room temperature
exceeds 30°C, such as in the summertime.
●
•
When sunlight is directly on the sensor area or a heater is
used in the bathroom, the sensor may detect incorrectly
due to the heat, resulting in the automatic operation of
functions such as auto lid opening and closing.
●
•
When the bathroom door is open, the sensor may detect
people who pass to the front or side of the toilet.
■
●
Body sensor B detects when someone stands in front
of the toilet bowl.
●
•
Body sensor B emits an infrared beam as shown in
the figure. When a person moves into the range of
this infrared beam, the sensor detects the person.
* Detection by the sensor may be difficult when the toilet
is used by someone small, such as a child.
Body sensor A
Body sensor B
< About the seat switch >
■
●
When you sit on the toilet seat, the seat switch turns ON,
enabling you to use various features.
(A click sound is heard when the seat switch is ACTIVATED.)
Seat switch
(Built-in)
Switch
ON
Gap
The toilet seat lowers.
■
●
Sit back on the toilet seat.
●
•
The seat switch will not turn on unless you sit
on the seat properly.
Note
●
•
When a child uses the NEOREST, the seat
switch may not be ACTIVATED by their light
body weight.
●
•
Since the toilet seat is designed to move up
and down, a clearance is provided between the
toilet seat cushion and the toilet bowl.
Grounding Instructions
This product should be grounded. In the event of an electrical short circuit, grounding
reduces the risk of electric shock by providing an escape wire for the electrical current.
The plug must be plugged into an outlet that is properly installed and grounded.
DANGER - Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire
to either flat-head terminal.
Check with a qualified electrician or serviceman if the grounding wire instructions are not
completely understood, or if in doubt as to whether the product is properly grounded.
This product is factory equipped with a specific electric cord and plug to permit connection
to a proper electric circuit. Make sure that the product is connected to an outlet having the
same configuration as the plug.
No adapter should be used with this product. Do not modify the plug provided - if it will not fit
in the outlet, have the proper outlet installed by a qualified electrician.
If the product must be reconnected for use on a different type of electric circuit, the
reconnection should be made by qualified service personnel.
If it is necessary to use an extension cord, use only a three wire extension cord that has a
three blade grounding plug, and a three-slot receptacle outlet that will accept the plug on the
product.
Replace or repair a damaged cord.
For Asia, Oceania, Middle East
Confirm that the earthing wire is securely connected.
Save these instructions.
IntroductionIntroduction
