Tosot TU18H3O Owner'S Manual Download Page 5

Page: 5 / 48

DC Inverter U-match Series Cassette Type Unit

1 Safety Precautions

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

This mark indicates procedures which, if improperly performed,

might lead to the death or serious injury of the user.

This mark indicates procedures which, if improperly performed,

might possibly result in personal harm to the user, or damage to

property.
NOTICE is used to address practices not related to personal injury.

(1)

This product can’t be installed at corrosive, inflammable or explosive environment

or the place with special requirements, such as kitchen. Otherwise, it will affect the

normal operation or shorten the service life of the unit, or even cause fire hazard

or serious injury. As for above special places, please adopt special air conditioner

with anti-corrosive or anti-explosion function.

(2)

Instructions for installation and use of this product are provided by the

manufacturer.

(3)

Installation must be performed in accordance with the requirements of NEC and

CEC by authorized personnel only.

(4)

Installation should be left to the dealer or another professional. Improper

installation may cause water leakage, electrical shock, or fire.

(5)

Install the air conditioner according to the instructions given in this manual.

Incomplete installation may cause water leakage, electrical shock, or fire.

(6)

Be sure to use the supplied or specified installation parts. Use of other parts may

cause the unit to come to lose, water leakage, electrical shock, or fire.

(7)

Install the air conditioner on a solid base that can support the weight of the unit. An

inadequate base or incomplete installation may cause injury in the event the unit

falls off the base.

(8)

Electrical work should be carried out in accordance with the installation manual

and the national electrical wiring rules or code of practice. Insufficient capacity or

incomplete electrical work may cause electrical shock or fire.

(9)

Be sure to use a dedicated power circuit. Never use a power supply shared by

another appliance.

(10)

For wiring, use a cable length enough to cover the entire distance with no

connection. Do not use an extension cord. Do not put other loads on the power

supply, use a dedicated power circuit. (Failure to do so may cause abnormal heat,

electric shock or fire.)

(11)

Use the specified types of wires for electrical connections between the indoor and

outdoor units. Firmly clamp the interconnecting wires so their terminals receive no

external stresses.

Incomplete connections or clamping may cause terminal

overheating or fire.

Summary of Contents for TU18H3O

















































Search results

Summary of Contents for TU18H3O

Reviews:

Related manuals for TU18H3O

Brands by name

Popular brands

Tosot TU18H3O, Owner'S Manual

Search results

Summary of Contents for TU18H3O

Reviews:

Related manuals for TU18H3O

Brands by name

Popular brands