Tosot TU18H3O Owner'S Manual Download Page 39 | Manualshive

Page: 39 / 48

background image

DC Inverter U-match Series Cassette Type Unit

35

!

6

If the indoor unit connection cord (to the outdoor unit) and power supply are wired

incorrectly, the air conditioner may be damaged.

7

Connect the indoor unit connection cord properly based on the corresponding

marks as shown from Fig.4.40 to Fig.4.42.

8

Ground both the indoor and outdoor units by attaching a ground wire.

9

Unit shall be grounded in compliance with the applicable local and national codes.

(6) Electric wiring of outdoor unit side

NOTICE:

When connecting the power supply cord, make sure that the phase of the power

supply matches with the exact terminal board. If not, the compressor will rotate
reversely and run improperly.

Remove the big handle /front board of the outdoor unit and insert the end of the

communication cord and the power cable into the terminal board.

Single phase:

Fig. 4.45

5 Installation of Controller

Refer to the Installation Manual of the controller for more details.

«
...
37
38
39
40
41
...
»

Summary of Contents for TU18H3O

















































Reviews:

No comments

Related manuals for TU18H3O

Brand: b-mola Pages: 16

Brand: Cooper & Hunter Pages: 63

Brand: ARCTIC WIND Pages: 17

Brand: Dimplex Pages: 11

C*ED060A Series

Brand: Unitary products group Pages: 24

PROFESSIONAL XL INN-560

Brand: INNOLIVING Pages: 28

Brand: Daikin Pages: 92

Brand: Arctic King Pages: 38

Brand: Heat Controller Pages: 5

SYMPHONY CHOIR WMMS-2x09K-V2B(46)2

Brand: YMGI Pages: 53

Brand: Daikin Pages: 282

Brand: Daikin Pages: 16

Brand: Daikin Pages: 273

Brand: Gree Pages: 18

Brand: Klimaire Pages: 28

TAC-07CHSA/XA71

Brand: TCL Pages: 41

Brand: Dadam micro Pages: 12

ELFOFresh2 CPAN-U 70-120 Series

Brand: CLIVET Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands