background image

DC Inverter U-match Series Cassette Type Unit

5

Indoor Unit Accessories

No.

Name

Appearance

Quantity

Usage

15

Bolt Assembly

4

Connect the panel and

body(only for 18k unit)

Table 3.2

Outdoor Unit Accessories

No.

Name

Appearance

Quantity

Usage

1

Drain Plug

1 or 3

To plug the unused drain

hole

2

Drainage

Connecter

or

1

To connect with the hard

PVC drain pipe

3.2 Selection of the Installation Location

!

1

The unit must be installed where strong enough to withstand the weight of the unit

and fixed securely, otherwise the unit would topple or fall off.

2

Do not install where there is a danger of combustible gas leakage.

3

Do not install the unit near heat source, steam, or flammable gas.

4

Children under 10 years old must be supervised not to operate the unit.

Decide the installation location with the customer as follows:

3.2.1 Indoor Unit

Select an installation site where the following conditions are fulfilled and that meets

your customer's approval.

(1) Obstruct should be put away from the intake or outlet vent of the indoor unit

so that the airflow can be blown through all the room.

(2) Make sure that the installation meets the requirement of the schematic

diagram of installation spaces.

(3) Select the place where can stand 4 times of the weight of the indoor unit and

would not increase the operating noise and vibration.

(4) The horizontality of the installation place should be guaranteed.
(5) Select the place where is easy to drain out the condensate water, and

connect with outdoor unit.

Summary of Contents for TU18H3O

















































Reviews: