Toshiba Satellite X200 Maintenance Manual Download Page 152

Page: 152 / 250

4.5 HDD

4 Replacement Procedures

Pull out the black Mylar tab to remove the HDD unit.

Figure 4-15

Removing the secondary HDD

Pull the HDD outwards and remove the four silver M3x3 screws that secure the HDD
case and brackets to the HDD.

Remove the HDD from the HDD case.

Installing the Main HDD

To install the main HDD, follow these steps and refer to the figures in the preceding section.

Seat the main HDD in the HDD case and brackets, and secure it with four silver M3

screws.

Insert the main HDD unit into the HDD slot on the left.

Secure the HDD door with one black M2.5x4 screw.

Installing the Secondary HDD

To install the secondary HDD, follow these steps and refer to the figures in the preceding
section.

Seat the secondary HDD in the HDD case and brackets, and secure it with four silver
M3

3 screws.

Insert the secondary HDD unit into the HDD slot on the right.

Secure the HDD door with two black M2.5x4 screws.

Satellite X200/ X205 Series Maintenance Manual

[CONFIDENTIAL]

4-17

Summary of Contents for Satellite X200



























































































































































































































































Search results

Summary of Contents for Satellite X200

Reviews:

Brands by name

Popular brands

Toshiba Satellite X200, Maintenance Manual

Search results

Summary of Contents for Satellite X200

Reviews:

Brands by name

Popular brands