Toshiba Satellite X200 Maintenance Manual Download Page 142

Page: 142 / 250

4.2 Battery

4 Replacement Procedures

4.2 Battery

Removing the Battery Pack

To remove the battery pack from the battery bay, follow these steps:

Turn the computer upside down.

Unlock the battery compartment lock.

Figure 4-1

Unlocking the battery lock

Slide the battery bay latch to release the battery pack and then remove the battery pack
from the bay.

Figure 4-2

Unlocking the battery lock

NOTE: For environmental reasons, do not throw away a spent battery pack.
Please return spent battery packs to Toshiba.

Satellite X200/ X205 Series Maintenance Manual

[CONFIDENTIAL]

4-7

Summary of Contents for Satellite X200



























































































































































































































































Search results

Summary of Contents for Satellite X200

Reviews:

Related manuals for Satellite X200

Brands by name

Popular brands

Toshiba Satellite X200, Maintenance Manual

Search results

Summary of Contents for Satellite X200

Reviews:

Related manuals for Satellite X200

Brands by name

Popular brands