manualshive.com logo in svg

Toshiba Satellite X200, Maintenance Manual

Share
Download
Toshiba Satellite X200 Maintenance Manual Download Page 141

4  Replacement Procedures 

4.1  General 

4-6 

[CONFIDENTIAL]

Satellite X200/ X205 Series Maintenance Manual 

Tools and Equipment 

The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the 
safety of those around you. Proper use of these devices will increase the success rate of your 
repairs and lower the cost for damaged or destroyed parts. The following equipment is 
necessary to disassemble and reassemble the computer:  

‰

 

One M2 Phillips screwdriver to remove and replace screws. 

‰

 

One T8 security screwdriver. 

‰

 

Tweezers, to lift out screws that you cannot grasp with your fingers. 

‰

 

ESD mats for the floor and the table you are working on. 

‰

 

ESD wrist strap or heel grounder. 

‰

 

Anti-static carpeting or flooring. 

‰

 

Air-ionizers in highly static sensitive areas. 

 

Summary of Contents for Satellite X200



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands