Toshiba Satellite M300 Page 201 Maintenance Manual Download

Page: 201 / 308

Replacement Procedures

Satellite M300 and Satellite Pro M300 Maintenance Manual (960-Q08)

4-38

Install the display assembly

The following describes the procedure for installing the display assembly (See Figure 4-13 to
4-17).

Insert the

pole

of hinge

to the

hole

of hinge assembly, set the

display assembly

on the

base assembly.

Secure the

hinges

with the following

screws

secure the

display mask

with the

following

screws

and stick the

mask seal

on them.

•

M2.5

5.0B BIND

screw

NOTE

Be sure to apply the lock tight to the screws instructed in the

figure above.

Connect the

LCD harness

to the connector on the system board.

Arrange the wireless antenna cables along the guide (front) and secure them with

guide

Pass the cables to the back of computer through the

slot

Arrange the

wireless LAN antenna

along the guide and contact with the connector.

Install the LAN board and top ASSY of the system.

Summary of Contents for Satellite M300





















































































































































































































































































































Search results

Summary of Contents for Satellite M300

Reviews:

Related manuals for Satellite M300

Brands by name

Popular brands

Toshiba Satellite M300, Maintenance Manual

Search results

Summary of Contents for Satellite M300

Reviews:

Related manuals for Satellite M300

Brands by name

Popular brands