Toshiba Satellite M300 Page 70 Maintenance Manual Download | Manualshive

Page: 70 / 308

background image

2 Troubleshooting Procedures

Satellite M300 and Satellite Pro M300 Maintenance Manual (960-Q08)

26

2.6 2.5” HDD Troubleshooting

To check if 2.5” HDD is malfunctioning or not, follow the troubleshooting procedures below
as instructed.

Procedure 1: Partition Check

Procedure 2: Message Check

Procedure 3: Format Check

Procedure 4: Diagnostic Test Program Execution Check

Procedure 5: Connector Check and Replacement Check

CAUTION: The contents of the hard disk will be erased when the 2.5” HDD

troubleshooting procedures are executed. Transfer the contents of the hard
disk to floppy disks or other storage drive(s). For the backup, refer to the
User’s Manual.

Procedure 1

Partition Check

Insert the Toshiba MS-DOS system disk and start the computer. Perform the following
checks:

Check 1

Input

C:

and press

Enter

. If you cannot change to drive C, go to Check 2. If you

can change to drive C, go to Procedure 2.

Check 2

Input

FDISK

and press

Enter

. Choose Display Partition Information from the

FDISK menu. If drive C is listed in the Display Partition Information, go to Check
3. If drive C is not listed, return to the FDISK menu and choose the option to
create a DOS partition or a logical DOS drive on drive C. If the problem still
occurs, go to Procedure 2.

Check 3

If drive C is listed as active in the FDISK menu, go to Check 4. If drive C is not
listed as active, return to the FDISK menu and choose the option to set the active
partition for drive C. Then go to Procedure 2.

Check 4

Remove the system disk from the FDD and reboot the computer. If the problem
still occurs, go to Procedure 2. Otherwise, the 2.5” HDD is operating normally.

«
...
68
69
70
71
72
...
»

Summary of Contents for Satellite M300





















































































































































































































































































































Reviews:

No comments

Related manuals for Satellite M300

Brand: Gateway Pages: 10

Brand: Gateway Pages: 87

600E - ThinkPad 2645 - PII 400 MHz

Brand: IBM Pages: 4

600E - ThinkPad 2645 - PII 400 MHz

Brand: IBM Pages: 4

2621483 - ThinkPad i Series 1400 2621

Brand: IBM Pages: 6

Brand: IBM Pages: 22

Brand: IBM Pages: 148

Brand: IBM Pages: 3

THINKPAD I 1200 -

Brand: IBM Pages: 233

VERSA LX AGP VIDEO -

Brand: NEC Pages: 14

Packard Bell 314

Brand: Acer Pages: 33

Predator 17 X GX-792

Brand: Acer Pages: 94

Predator Triton 500 SE

Brand: Acer Pages: 105

Predator Helios 700

Brand: Acer Pages: 98

Predator Helios 500

Brand: Acer Pages: 90

PREDATOR 15 G9-591

Brand: Acer Pages: 90

Brand: Acer Pages: 16

Brand: ARIMA Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands