manualshive.com logo in svg

Toshiba Satellite L350D series, Maintenance Manual

The Toshiba Satellite L350D series Maintenance Manual is an invaluable resource for users seeking to keep their laptops in optimal condition. This comprehensive manual, available for free download at manualshive.com, provides detailed instructions and troubleshooting tips, empowering users to handle maintenance tasks with ease and confidence.

Share
Download
background image

2.3  Power Supply 

2  Troubleshooting 

Satellite L350D/Satellite Pro L350D/EQUIUM L350D/SATEGO L350D     Maintenance Manual 2-7 

‰

 

 DC IN LED 

DC IN LED 

Power supply status 

On in Green  

DC power being supplied (from the AC adapter) 

Off 

Battery damage and can’t charge during DC-in.

 

Off Else

 

 

If the DC IN LED off, follow the steps below: 

1.

 

Remove the battery pack and the AC adapter to shut off power supply to the 
computer. 

2.

 

Attach the battery and AC adapter back again. 

If the LED still off, follows the steps below: 

 

Check 1 

Make sure the DC IN LED goes on in Green.  If it does not, go to Procedure 2. 

 

Check 2 

Make sure the Battery LED goes on in Amber or Green or Orange.  If it does 
not, go to Procedure 3. 

 

Summary of Contents for Satellite L350D series

























































































































































































































































Reviews:

No comments

Related manuals for Satellite L350D series

BELINEA b.book 5.1 User Manual preview
b.book 5.1
Brand: BELINEA Pages: 48
Samsung Galaxy Book Flex User Manual preview
Galaxy Book Flex
Brand: Samsung Pages: 119
Fujitsu LifeBook S762 Operating Manual preview
LifeBook S762
Brand: Fujitsu Pages: 104
Fujitsu Lifebook S761 User Manual preview
Lifebook S761
Brand: Fujitsu Pages: 394
Fujitsu Lifebook T900 User Manual preview
Lifebook T900
Brand: Fujitsu Pages: 416
Fujitsu Lifebook S760 User Manual preview
Lifebook S760
Brand: Fujitsu Pages: 415
Fujitsu Lifebook S904 Operating Manual preview
Lifebook S904
Brand: Fujitsu Pages: 94
Fujitsu LIFEBOOK P3110 Upgrade preview
LIFEBOOK P3110
Brand: Fujitsu Pages: 36
Huawei 53012GDQ Quick Start Manual preview
53012GDQ
Brand: Huawei Pages: 28
Huawei MateBook D Quick Start Manual preview
MateBook D
Brand: Huawei Pages: 41
Huawei MateBook E User Manual preview
MateBook E
Brand: Huawei Pages: 39
Huawei MateBook HZ-W09 Quick Start Manual preview
MateBook HZ-W09
Brand: Huawei Pages: 168
Huawei matebook 16s cref-x Quick Start Manual preview
matebook 16s cref-x
Brand: Huawei Pages: 23
Huawei BohL-WDQ9 Quick Start Manual preview
BohL-WDQ9
Brand: Huawei Pages: 39
Huawei CREM-WFD9 Quick Start Manual preview
CREM-WFD9
Brand: Huawei Pages: 28
Huawei MateBook 13 Quick Start Manual preview
MateBook 13
Brand: Huawei Pages: 110
Huawei MDZ-WDH9A Quick Start Manual preview
MDZ-WDH9A
Brand: Huawei Pages: 28
Huawei MateBook D 14 Quick Start Manual preview
MateBook D 14
Brand: Huawei Pages: 297

Brands by name

Popular brands

Load more brands