Toshiba Satellite L350D series Maintenance Manual Download Page 26

Page: 26 / 248

1 Hardware Overview

1B1.2 System Unit Components

Satellite L350D/Satellite Pro L350D/EQUIUM L350D/SATEGO L350D Maintenance Manual

The system unit of the computer consists of the following components:

Processor: AMD Turion64 X2 and Athlon X2 Processor.

Turion64 X2 Processor

−

Core Speed: 2.0 GHz

−

I/O Bus: 1600 MHz

−

On-die Level 2 Cache: 1 MB

Athlon X2 Processor

−

Core Speed: 1.9 GHz

−

I/O Bus: 1600 MHz

−

On-die Level 2 Cache: 1 MB

Memory

Two expansion memory slots are provided. They can hold 512/1024/2048/4096MB
expansion memory modules available as options to grow up to 8.0 GB.

PC2-5300 (667MHz) / PC2-6400 (800MHz) DDRII SDRAM supported

512/1024/2048/4096MB modules supported

−

512 MB (64M x 64)

−

1024 MB (128M x 64)

−

2048 MB (256M x 64)

−

4096 MB (512M x 64)

1.8 volt operation

No parity bit

64-bit data transfer

BIOS ROM (Flash EEPROM)

8Mb x 1 chip (1024KB flash parts)

−

NvStorage Size: 64KB

−

NvStorage Free Space: 37KB

−

FV00 Size: 652KB

−

FV00 Free Space: 72KB

−

FV01 Size: 32KB

−

FV01 Free Space: 5KB

−

FV02 Size: 36KB

−

FV02 Free Space: 3KB

−

FV03 Size: 52KB

−

FV03 Free Space: 2KB

Summary of Contents for Satellite L350D series

























































































































































































































































Search results

Summary of Contents for Satellite L350D series

Reviews:

Related manuals for Satellite L350D series

Brands by name

Popular brands

Toshiba Satellite L350D series, Maintenance Manual

Search results

Summary of Contents for Satellite L350D series

Reviews:

Related manuals for Satellite L350D series

Brands by name

Popular brands