Toshiba Satellite L350D series Maintenance Manual Download Page 148

Page: 148 / 248

4 Replacement Procedures

4.1 General

Removing the Memory Card

Remove the memory card according to the following procedures and Figure 4-3, after
checking that the computer is turned off in boot mode.

Open the card cover.

Push the memory card to be removed until it stops then release the memory card.

When the memory card pops out, grasp it and pull it out.

Memory card

Figure 4-3 Removing the memory card

4-12

Satellite L350D/ Satellite Pro L350D/ EQUIUM L350D/ SATEGO L350D

Maintenance Manual

Summary of Contents for Satellite L350D series

























































































































































































































































Search results

Summary of Contents for Satellite L350D series

Reviews:

Related manuals for Satellite L350D series

Brands by name

Popular brands

Toshiba Satellite L350D series, Maintenance Manual

Search results

Summary of Contents for Satellite L350D series

Reviews:

Related manuals for Satellite L350D series

Brands by name

Popular brands