Toshiba RAS-B10N3KV2-E Service Manual Download Page 79

Page: 79 / 105

–

Table 11-8-1

No.

Procedure

Turn off the power supply breaker
and remove the P.C. board
assembly from electronic parts
base. Remove the connecting
cables from the terminal block.

Remove the connector of the
motor and turn on the power
supply breaker. If OPERATION
indicator flashes (once per
second), it is not necessary to
check steps (1 to 3) in the right
next column.

Push [ ] button once
to start the unit. (Do not set the
mode to On-Timer operation.)

Shorten the restart delay timer
and start unit.

Push [ ] button once to start
the unit.

• Shorten the restart delay timer.

• Set the operation mode to

COOL.

• Set the fan speed level to

AUTO.

• Set the preset temperature

much lower than the room
temperature. (The unit (com-
pressor) operates continuously
in the above condition.)

If the above condition (No. 5) still
continues, start the unit in the
following condition.

• Set the operation mode to

HEAT.

• Set the preset temperature

much higher than room tem-
perature.

Connect the motor connector to
the motor and turn on the power
supply.
Start the unit the following
condition.

• Set the fan speed level to HIGH.

(The unit (compressor) operates
continuously in the above
condition in No. 5.)

Check points

Check whether or not the fuse (F01)
is blown.

Check power supply voltage :

1. Between No. 1 and No. 3 of CN01

(AC 220–240V)

2. Between

and

of C27

(DC 310–340V)

3. Between 12V and GND
4. Between 5V and GND

Check power supply voltage :

1. Between CN51 and

No. 1 of CN01 (DC 15–60V)

Check whether or not all indicators
(OPERATION,TIMER,FILTER,PRE.DEF,
Hi POWER) are lit for 3 seconds and

they return to normal 3 seconds later.

1. Check whether or not the

compressor operates.

2. Check whether or not the

OPERATION indicator flashes.

1. Check whether or not the

compressor operates.

2. Check whether or not the

OPERATION indicator flashes.

1. Check it is impossible to detect

the voltage (AC120V or higher
voltage) between red and black

2. The motor does not operate or

the fan motor does not rotate with
high speed.
(But it is possible to receive the

signal from the remote controller.)

3. The motor rotates but vibrates

Causes

Impulse voltage was applied or the
indoor fan motor short-circuited.

1. The terminal block or the crossover

cable is connected wrongly.

2. The capacitor (C01), line filter

(L01), resistor (R64), or the diode
(DB01) is defective.

3. T01 is defective.

4. IC02 and T01 are defective.

IC51 and IC52 are defective.

The indicators are defective or the
housing assembly (CN21) is defective.

1. The temperature of the indoor heat

exchanger is extremely low.

2. The connection of the heat

exchanger sensor is loose.
(The connector is disconnected.)
(CN62)

3. The heat exchanger sensor and the

P.C. board are defective.
(Refer to Table 11-4-1.)

4. The main P.C. board is defective.

1. The temperature of the indoor heat

exchanger is extremely high.

2. The connection of the heat

exchanger sensor short-circuited.
(CN62)

3. The heat exchanger sensor and the

P.C. board are defective.
(Refer to Table 11-4-1.)

4. The main P.C. board is defective

1. The indoor fan motor is defective.

(Protected operation of P.C. board.)

2. The P.C. board is defective.

3. The connection of the motor

connector is loose.

lead of the motor.

strongly.

FILE NO. SVM-12050

(3) Check procedures

Summary of Contents for RAS-B10N3KV2-E










































































































Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands

Toshiba RAS-B10N3KV2-E, Service Manual

Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands