Toshiba RAS-B10N3KV2-E Service Manual Download Page 74

Page: 74 / 105

FILE NO. SVM-12050

Press [ ]

button.

Is transmission

mark indicated?

Press RESET button

on remote control

with tip of pencil.

Is receiver on

indoor unit exposed

to direct sunlight?

Is there any

thyristor fluorescent

light nearby?

Does indoor unit

operate when

moving remote control

near receiver or

indoor unit?

Press [ ]

button.

Batteries are

exhausted.

Is transmission mark

indicated?

Does indoor unit

beep and operate?

Remote control

is defective.

Does indoor unit

start to operate by

automatic restart

function?

Does radio sound

is affected by

remote control when

a signal is transmitted

at distance of 5 cm

from radio?

P.C. board is

defective.

Keep indoor unit

away from

thyristor

fluorescent light.

Avoid direct

sunlight.

Replace

P.C. board.

Replace

batteries.

Normal

operation

Replace

remote control.

The unit does not beep at all.
OPERATION lamp on
indoor unit is not indicated.

YES

(4) Troubleshooting for remote control

– 73 –

Summary of Contents for RAS-B10N3KV2-E










































































































Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands

Toshiba RAS-B10N3KV2-E, Service Manual

Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands