Toshiba RAS-B10N3KV2-E Service Manual Download Page 42

Page: 42 / 105

Item

Operation flow and applicable data, etc.

Description

18. Hi-POWER ([Hi-POWER] button on the remote controller

is pressed)

When [Hi-POWER] button is pressed while the indoor
unit is in Auto, Cooling or Heating operation, Hi-

Mode

POWER mark is indicated on the display of the remote

controller and the unit operates as follows.

1. Automatic operation

•

The indoor unit operates in according to the

current operation.

2. Cooling operation

remote controller does not change.)
The indoor unit's fan speed level increase 1 tap

•

The preset temperature drops 1ºC

(The value of the preset temperature on the

3. Heating operation

remote controller does not change.)
The indoor unit's fan speed level increase 1 tap

•

The preset temperature increases 2ºC

(The value of the preset temperature on the

4. The Hi-POWER mode can not be set in Dry

operation

19. FILTER When the elapsed time reaches 1000 hours after

Indicator

air conditioner operation, the FILTER indicator lights.
After cleaning the filters, turn off the FILTER indicator.

How to Turn Off FILTER Indicator
Press [RESET] button on the indoor unit.

NOTE :

If [RESET] button is pushed while the FILTER indicator

is not lit, the indoor unit will start the automatic
operation.

−

FILE NO. SVM-12050

Summary of Contents for RAS-B10N3KV2-E










































































































Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands

Toshiba RAS-B10N3KV2-E, Service Manual

Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands